Retronetworking

h1. Philips TA Mini Pad Euro

A ISDN TA made by Philips.

Variants

|_.Model|_.D-channel protocol|_.notes|_.Ident number|

| TA mini     | DSS1/Euro | without PAD | 245 536 |

| TA mini     | 1TR6      | without PAD | 245 537 |

| TA mini PAD | Euro/Euro | with PAD    | 245 538 |

| TA mini PAD | 1TR6      | with PAD    | 245 539 |

h2. Hardware

{{thumbnail(Philips_TA_Mini_Pad_Euro_front.jpg)}}

{{thumbnail(Philips_TA_Mini_Pad_Euro_back.jpg)}}

{{thumbnail(Philips_TA_Mini_Pad_Euro_bottom.jpg)}}

{{thumbnail(Philips_ISDN_TA_Mini-pcb-perspective.jpg)}}

{{thumbnail(Philips_ISDN_TA_Mini-pcb-top1.jpg)}}

{{thumbnail(Philips_ISDN_TA_Mini-pcb-top2.jpg)}}

{{thumbnail(Philips_ISDN_TA_Mini-pcb-top3.jpg)}}

{{thumbnail(Philips_ISDN_TA_Mini-pcb-top4.jpg)}}

{{thumbnail(Philips_ISDN_TA_Mini-pcb-top5.jpg)}}

{{thumbnail(Philips_ISDN_TA_Mini-pcb-bottom1.jpg)}}

{{thumbnail(Philips_ISDN_TA_Mini-case1.jpg)}}

{{thumbnail(Philips_ISDN_TA_Mini-case2.jpg)}}

{{thumbnail(Philips_ISDN_TA_Mini-manual.jpg)}}

|Supply Voltage|12V AC|

|Power Consumption|~4.2W|

|RS232 Connector|DB25|

|Line Connector|RJ45|

h2. AT-Commands

<pre>

# authorize (default-pw: 1234)

AT%L1234

<pre>

AT%L1234

R/W access

OK

ATI

AT.. - prefix                        A/   - repeat last command

ATA  - connect incoming call         ATD  - dial command

ATE  - echo mode                     ATH  - disconnect

ATI  - information                   ATO  - connect

ATQ  - surpress feedback             ATS  - read/write S register

ATV  - feedback verbal/numeric       ATX  - extended output format

ATZ  - load stored profile           AT&C - DCD mode

AT&D - DTR mode                      AT&F - load factory setting

AT&P - select protocol               AT&R - CTS/RTS mode

AT&S - DSR mode                      AT&T - tests/loops

AT&V - list profile                  AT&W - store profile

AT&Z - store/list number             AT$B - set HDLC mode block size

AT$D - direct call                   AT$F - set HDLC mode flow ctrl.

AT$I - data guard                    AT$L - activate SW download

AT$S - set rate adapt. prot.         AT$X - extended ISDN info output

AT%C - charging information          AT%H - ISDN history buffer

AT%I - ISDN connection status        AT%M - select menu

AT%P - portlines status              AT%S - ISDN statistics

AT%Y - X.25 history buffer           AT#D - set/read date

AT#T - set/read time·················

OK

ATI1

PHILIPS  TA mini·

Product Code 245 538

Software Version 2.10 DSS1

Country Code = 04

OK

ATI2

.............. CHECK SUM = 886C

OK

ATI3

Hardware Version 4.0 (Flash EPROM AB)

OK

ATI4

Internal Test running ...

T&V

Data Port Profile 1:

access control   = off               outside line     =·················

S mode           = dial connection   LAPD             = disconnect idle·

data service     = unrestricted 64k  TEI              = #  automatic····

default number   = # dial. from DTE  dial-in number   =·················

DTE protocol     = AT command set    character mode   = asynchronous····

rate adapt.prot. = V.110/X.30        data rate        = 2.4kbit/s·······

connector        = 25-pole V.28      DTR/C mode       = 2:DTReady  108/2

DSR mode         = 2:ready for data  RTS/CTS mode     = 3: DTR -> CTS···

DCD/I mode       = 2:DTR/C -> DCD/I  dataguard        = off·············

stopbits         = 1                 databits/parity  = 7/even··········

echo             = off               ISDN info. outp. = causes··········

E0 Q0 V1 X2 &C1 &D2 &R1 &S1 $D0 $X2 $O0A

S00=001 S01=000 S02=043 S03=013 S04=010 S05=008

S12=050 S14=0AH S21=74H S22=20H S23=00H S27=00H

OK

Data Port 1:····

no connection···

OK

</pre>