Bintec X1200 » History » Revision 5
Revision 4 (laforge, 10/23/2022 01:49 PM) → Revision 5/6 (laforge, 10/23/2022 02:10 PM)
h1. Bintec X1200 {{>toc}} The Bintec X1200 is a ISDN router featuring two ISDN BRI lines on the WAN side and a single ethernet connecton on the LAN side. It apparently supports remote CAPI (CAPI over TCP). h2. Hardware * Motorola XPC860DTZP50D3 PowerPC processor * Samsung K4S643232C-TC10 SDRAM * Sharp LH28F016SCHT-L95 Flash * Infineon PSB2115H V1.1 IPAC ISDN Interface IC * Lucent LU3x31FT2J80 Ethernet Transceiver IC * LevelOne LXT905LC Ethernet PHY * Maxim MAX202ECWE RS232 trasnceiver IC * Maxim DS1314S NVRAM controller IC * 5.5V 1.0F supercap (for NVRAM) h2. Serial Console h3. Power up <pre> ### X1200 (Hardware-Rev. 1.2, Firmware-Rev. 6.0) ### CPU Check ... passed (MPC 8XXT D3) SDRAM Check ........ passed (8 MByte) FLASH Check .. passed (2 MByte) ISDN Check ... passed 100BT Check ... passed 10BT Check ... passed ### Selftest passed ### Press <sp> for boot monitor or any other key to boot system </pre> h3. Bootmonitor <pre> X1200 Bootmonitor V.6.2 Rev. 8 from 2003/01/23 00:00:00 Copyright (c) 1999-2002 by BinTec Communications AG (1) Boot System (2) Software Update via TFTP (3) Software Update via XMODEM (4) Delete Configuration (5) Default Bootmonitor Parameters (6) Show System Information Your Choice> 6 ### Start System information ### Identification: BINTEC X1000 Hardware: 1.2 Serial: X1B120000370449 Ethernet MAC 100BT: 00:a0:f9:02:4b:70 Flash: 2047 K/byte RAM: 8127 K/byte ### Current Software Logik: 6.0 Bootmon: V.6.2 Rev. 8 from 2003/01/23 00:00:00 Boss: 6.2.5 ### more info ID: X1B Name: X1200 Company (short): BINTEC Type: X1200 Company (long): BinTec Communications AG Features: 0 ### End System information ### </pre> <pre> Your Choice> 4 Deleting the configuration will reset your router to factory state. Ready to continue ? (y or n) ? y Delete configuration now ? (y or n) ? y Configuration deleted </pre> h3. firmware booting <pre> Booting Image from Flash ROM Checking image ... OK Writing image to RAM (Release 6.2.5) .............................................................................................................................. OK (3990772 bytes) Booting BOSS... boss image started at 0x212400 BOSS PPC kernel v2.0 (X1200) Copyright (c) 1999-2000 by BinTec Communications AG Version V.6.2 Rev. 5 (Patch 1) IPSec V. 2.1.1 from 2002/10/17 00:00:00 The system is coming up. Speed index... 49.81 MIPS The system is ready. AUTOEXEC: 1 date Sat May 28 21:42:55 2016 done 1 configd SystemId: X1B120000370449 Cfg: (default) done 10 isdnd background 11 isdnautocf background 20 x25swd background 21 mpxd background 50 ipd background 51 snmpd background 51 telnetd background 51 syslogd background 51 minipadd background 51 txd background 67 pppxd background 68 pppoed background 69 tud background 70 radiusd background 70 pppd background 90 timed background 97 ipalived background 98 statusd background 99 bootpd background 99 ddnsd background 99 traced background 99 dnsd background 99 resolvd background 99 isdnlogind background 99 vcapid background 99 ipsecd background </pre> h2. Default login credentials after erasing config User: @admin@, Password: @bintec@ h2. Remote CAPI bintec supports _Remote CAPI_, i.e. clients on the LAN can use CAPI encapsulated over TCP in order to utilize the ISDN capabilities of the BinTec router. Unfortunately, Linux libcapi20 contains a bug regarding the message header length. You need to apply the following fix in order to make libcapi20 interoperate: https://build.opensuse.org/package/view_file/home:mnhauke:ISDN/libcapi20/0001-Fix-remote-CAPI-sent-CAPI-Message-length.patch?expand=1 In order to use rcapi, you have to put a line like this in your @~/.capi20rc@: <pre> REMOTE rcapi 192.168.100.222 2662 </pre> where 192.168.100.222 is the IP address of te BinTec router. @capiinfo@ then will show somsething like this: <pre> Number of Controllers : 1 Controller 1: Manufacturer: BinTec Access Networks GmbH CAPI Version: 1073741826.1229996355 Manufacturer Version: 825110816.808333871 Serial Number: 1510449 BChannels: 2 Global Options: 0x00000019 internal controller supported DTMF supported Supplementary Services supported B1 protocols support: 0x00000047 64 kbit/s with HDLC framing 64 kbit/s bit-transparent operation V.110 asynconous operation with start/stop byte framing 56 kbit/s bit-transparent operation B2 protocols support: 0x00001a2b ISO 7776 (X.75 SLP) Transparent LAPD with Q.921 for D channel X.25 (SAPI 16) Point-to-Point Protocol (PPP) V.120 asyncronous mode V.120 bit-transparent mode LAPD with Q.921 including free SAPI selection B3 protocols support: 0x0000000f Transparent T.90NL, T.70NL, T.90 ISO 8208 (X.25 DTE-DTE) X.25 DCE 0100 0200 19000000 47000000 2b1a0000 0f000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 Supplementary services support: 0x0000003d Hold / Retrieve ECT 3PTY Call Forwarding Call Deflection </pre> </pre>
