Wiki » History » Version 30
laforge, 03/04/2020 08:38 PM
1 | 1 | tsaitgaist | h1. Osmocom SIMtrace 2 |
---|---|---|---|
2 | 15 | mschramm | |
3 | {{>toc}} |
||
4 | 1 | tsaitgaist | |
5 | 8 | laforge | Osmocom SIMtrace 2 is a software, firmware and hardware system for passively tracing SIM-ME communication between the SIM card and the mobile phone, and remote SIM operation. |
6 | 9 | tsaitgaist | While it was designed for SIM-ME communication, it supports all ISO 7816 smart-cards using the T=0 protocol (the most common case). |
7 | 1 | tsaitgaist | |
8 | 16 | roh | It is a followup of the "SIMtrace project":/projects/simtrace/wiki, providing more functionalities (e.g. remote SIM operation) and supporting multiple boards (e.g. SIMtrace with SAM3S, "sysmoQMOD":https://www.sysmocom.de/products/sysmoqmod/index.html). |
9 | 1 | tsaitgaist | |
10 | h2. Hardware |
||
11 | |||
12 | 10 | tsaitgaist | The SIMtrace 2 firmware supports several boards. |
13 | The firmware is written for an "ATSAM3S4B":https://www.microchip.com/wwwproducts/en/ATSAM3S4B micro-controller. |
||
14 | 1 | tsaitgaist | |
15 | 12 | tsaitgaist | Note: The SAM3S is meanwhile labelled as _not recommended for new designs_ by Atmel. However, there are plenty of hardware and software compatible upgrade options, including SAM4S. The upgrade is possible in the future. |
16 | 1 | tsaitgaist | |
17 | 26 | tsaitgaist | h3. SIMtrace board for SIMtrace 2 project |
18 | 1 | tsaitgaist | |
19 | 10 | tsaitgaist | !{width:20%}simtrace-board-mini.jpg! |
20 | 9 | tsaitgaist | |
21 | 10 | tsaitgaist | The main purpose of this board is to sniff the communication between a phone and a SIM card (or any card reader and smart-card). |
22 | 1 | tsaitgaist | |
23 | 17 | roh | This is the same circuit board as the previous "SIMtrace v1":/projects/simtrace/wiki/SIMtrace_Hardware, with the exception that the "ATSAM3S4B":https://www.microchip.com/wwwproducts/en/ATSAM3S4B micro-controller replaces the old "AT91SAM7S64":https://www.microchip.com/wwwproducts/en/AT91SAM7S64. Since the SAM3S is pin compatible with the SAM7S, any SIMtrace v1 board can be converted into a SIMtrace v2 board simply by replacing the micro-controller. |
24 | 1 | tsaitgaist | |
25 | 10 | tsaitgaist | Note: This hardware is "open source":https://git.osmocom.org/simtrace/tree/hardware. |
26 | 1 | tsaitgaist | |
27 | 27 | laforge | h4. SIMtrace2 hardware availability |
28 | |||
29 | Fully assembled SIMtrace2 boards and related accessories like FPC cables can be obtained from the "sysmocm webshop":http://shop.sysmocom.de/products/simtrace |
||
30 | |||
31 | 1 | tsaitgaist | h3. sysmoQMOD |
32 | |||
33 | !{width:25%}sysmoqmod.png! |
||
34 | |||
35 | The SAM3S micro-controller with SIMtrace 2 firmware is also used on the "sysmoQMOD":https://www.sysmocom.de/products/sysmoqmod/index.html board to provide remote SIM operation capabilities. |
||
36 | |||
37 | Note: This hardware is not open source. |
||
38 | 27 | laforge | |
39 | h4. sysmoQMOD hardware availability |
||
40 | |||
41 | Fully assembled sysmoQMOD boards and related products can be obtained from "sysmocom":https://www.sysmocom.de/products/lab/sysmoqmod/index.html - please contact sales@sysmocom.de for related inquiries. |
||
42 | 1 | tsaitgaist | |
43 | h2. Firmware |
||
44 | |||
45 | 10 | tsaitgaist | The SIMtrace 2 firmware source code is available in "git":https://git.osmocom.org/simtrace2/. |
46 | 20 | tsaitgaist | Pre-built firmware binaries are available "here":http://ftp.osmocom.org/binaries/simtrace2/firmware/. |
47 | The firmware are currently under active development and we recommend to [[Flashing|flash]] the new firmware images to profit from the latest bug fixes and added functionalities. |
||
48 | 1 | tsaitgaist | |
49 | The SIMtrace 2 firmware is a complete rewrite and *can only be flashed on hardware with SAM3S* ARM Cortex-M3-based micro-controllers. |
||
50 | 18 | roh | *The SIMtrace 2 firmware is not compatible with the older "SIMtrace v1":/projects/simtrace/wiki/SIMtrace_Hardware using SAM7S ARM7TDMI-based micro-controllers.* |
51 | 1 | tsaitgaist | |
52 | 23 | tsaitgaist | To get the version of the firmware flashed on the device: |
53 | * connect a USB to UART cable either to the 2.5 mm stereo headphone connector (tip = TX, ring = RX, sleeve = GND) or the nearby DEBUG port (pin 1 = GND, pin 4 = TX, pin 5 = RX) |
||
54 | * open the serial port with the following configuration: 921600 8N1 (115200 8N1 before version 0.5.1.2-80d9 from 2018-08-28) |
||
55 | * reboot the board using the RESET button or by re-plugging the USB connector |
||
56 | * you should see a banner containing the version information: |
||
57 | |||
58 | <pre> |
||
59 | ============================================================================= |
||
60 | SIMtrace2 firmware 0.4.195-acb7 (C) 2010-2016 by Harald Welte |
||
61 | ============================================================================= |
||
62 | </pre> |
||
63 | |||
64 | 12 | tsaitgaist | h3. trace |
65 | 1 | tsaitgaist | |
66 | 12 | tsaitgaist | The trace application firmware allow to sniff the communication between a phone and a SIM card (or any card reader and smart-card). |
67 | It is intended for the [[Wiki#SIMtrace v2|SIMtrace v2 hardware]] and its function is analog to the "SIMtrace v1":/projects/simtrace/wiki/SIMtrace_Firmware. |
||
68 | 10 | tsaitgaist | |
69 | 12 | tsaitgaist | The sniffing is completely passive. It uses the RST, ATR, PPS (baud rate tested with F/D up to 512/32), and WT (waiting timeout) to properly parse the ISO 7816-3 TPDUs. |
70 | Currently only the T=0 protocol is supported since this is the most common protocol used (we haven't seen T=1 in use). |
||
71 | |||
72 | 1 | tsaitgaist | !{width:25%}simtrace_and_phone.jpg! |
73 | 10 | tsaitgaist | |
74 | 20 | tsaitgaist | The application firmware to be flashed using [[Flashing#DFU|DFU]] is "simtrace-trace-dfu.bin":http://ftp.osmocom.org/binaries/simtrace2/firmware/simtrace-trace-dfu.bin. |
75 | 10 | tsaitgaist | |
76 | 24 | tsaitgaist | h3. card emulation |
77 | |||
78 | 25 | tsaitgaist | The card emulation application firmware allows to emulate a card (e.g SIM). This is useful if you don't want to change the card in the device (e.g. phone), or have the card in a remote location. |
79 | 24 | tsaitgaist | |
80 | This firmware comes preflashed on the sysmoQMOD board. |
||
81 | 1 | tsaitgaist | It also exists from the SIMtrace v2 board, but is currently in beta. If you still would like to try it, read this [[Cardem|article]]. |
82 | 25 | tsaitgaist | |
83 | *Do not use the @simtrace-cardem-dfu.bin@ firmware from the [[Wiki#Firmware|firmware repository]] since this currently does not include the fixes from the beta firmware.* |
||
84 | 24 | tsaitgaist | |
85 | 13 | tsaitgaist | h3. Development |
86 | |||
87 | To compile the firmware using the source code, or participate in the development, please refer to the instructions provided in the "README":https://git.osmocom.org/simtrace2/tree/firmware/README.txt . |
||
88 | |||
89 | 10 | tsaitgaist | h2. Flashing |
90 | 11 | tsaitgaist | |
91 | 1 | tsaitgaist | The [[Wiki#Firmware|firmware images]] can be flashed as described [[Flashing|here]]. |
92 | |||
93 | h2. Host PC Software |
||
94 | |||
95 | 13 | tsaitgaist | The SIMtrace 2 host PC software are available in the "simtrace2 git":https://git.osmocom.org/simtrace2/. |
96 | |||
97 | h3. Preconditions |
||
98 | |||
99 | 22 | jbruckner | [[libosmocore:]], libpcsclite and libusb. |
100 | 13 | tsaitgaist | |
101 | 22 | jbruckner | to install those packages: |
102 | 13 | tsaitgaist | <pre> |
103 | 22 | jbruckner | sudo apt-get install libusb-1.0-0-dev libosmocore-dev libpcsclite-dev |
104 | 13 | tsaitgaist | </code></pre> |
105 | |||
106 | h3. Compiling it |
||
107 | |||
108 | <pre> |
||
109 | git clone git://git.osmocom.org/simtrace2.git |
||
110 | cd simtrace2/host/ |
||
111 | 28 | roh | autoreconf -fi |
112 | ./configure |
||
113 | 13 | tsaitgaist | make |
114 | </pre> |
||
115 | |||
116 | h3. Accessing it |
||
117 | |||
118 | Add udev rules so to be able to use SIMtrace 2 devices and access the device as non-root user: |
||
119 | <pre> |
||
120 | # add current user to plugdev group (user needs to re-login for this change to take effect) |
||
121 | sudo adduser $USERNAME plugdev |
||
122 | # grant access permission to SIMtrace 2 for plugdev group |
||
123 | 29 | roh | sudo wget -O /etc/udev/rules.d/99-simtrace2.rules https://git.osmocom.org/simtrace2/plain/host/contrib/99-simtrace2.rules |
124 | 13 | tsaitgaist | # reload udev rules |
125 | sudo udevadm control --reload-rules |
||
126 | sudo udevadm trigger |
||
127 | </pre> |
||
128 | |||
129 | h3. Applications |
||
130 | |||
131 | h4. simtrace2-list |
||
132 | |||
133 | @simtrace2-list@ allows to list all SIMtrace 2 compatible devices: |
||
134 | <pre> |
||
135 | ./simtrace2-list |
||
136 | USB matches: 1 |
||
137 | 1d50:60e3 Addr=4, Path=2-2.3, Cfg=1, Intf=0, Alt=0: 255/1/0 (SIMtrace Sniffer) |
||
138 | </pre> |
||
139 | |||
140 | This is useful when you have multiple devices (such as with the [[Wiki#sysmoQMOD]]) and have to specific with device to use by the other applications. |
||
141 | |||
142 | h4. simtrace2-sniff |
||
143 | |||
144 | This will use the [[Wiki#trace|trace]] firmware and retrieve the sniffed phone-SIM communication. |
||
145 | The activity will be shown on the consol output: |
||
146 | <pre> |
||
147 | ./simtrace2-sniff |
||
148 | simtrace2-sniff - Phone-SIM card communication sniffer |
||
149 | (C) 2010-2017 by Harald Welte <laforge@gnumonks.org> |
||
150 | (C) 2018 by Kevin Redon <kredon@sysmocom.de> |
||
151 | |||
152 | Using USB device 1d50:60e3 Addr=4, Path=2-2.3, Cfg=1, Intf=0, Alt=0: 255/1/0 (SIMtrace Sniffer) |
||
153 | Entering main loop |
||
154 | Card state change: reset hold |
||
155 | Card state change: reset release |
||
156 | ATR: 3b 9f 96 80 1f c7 80 31 a0 73 be 21 13 67 43 20 07 18 00 00 01 a5 |
||
157 | PPS: ff 10 96 79 |
||
158 | PPS: ff 10 96 79 |
||
159 | Fi/Di switched to 512/32 |
||
160 | TPDU: a0 a4 00 00 02 3f 00 9f 22 |
||
161 | TPDU: a0 a4 00 00 02 7f 20 9f 22 |
||
162 | TPDU: a0 a4 00 00 02 6f 46 9f 0f |
||
163 | TPDU: a0 b0 00 00 11 81 43 43 43 20 45 76 65 6e 74 ff ff ff ff ff ff ff 90 00 |
||
164 | Card state change: reset hold |
||
165 | </pre> |
||
166 | |||
167 | The TPDU will also be sent the GSMTAP frames to UDP/IPv4 localhost:4729. |
||
168 | This also allows to analyze the communication in wireshark using the GSM SIM dissector. |
||
169 | 1 | tsaitgaist | !{width:50%}wireshark-sim.png! |
170 | 21 | laforge | |
171 | {{include(cellular-infrastructure:MacroBinaryPackages)}} |
||
172 | 30 | laforge | {{include(cellular-infrastructure:MacroCommercialSupport)}} |