Osmo-nitb VTY » History » Version 1
Anonymous, 02/19/2016 10:48 PM
initial vty and config file reference
| 1 | 1 | This page is a reference fo all VTY commands, both for interactive use at the command line, as well as for the configuration file. |
|
|---|---|---|---|
| 2 | |||
| 3 | == configuration reference == |
||
| 4 | |||
| 5 | === network level === |
||
| 6 | |||
| 7 | ==== network country code ==== |
||
| 8 | |||
| 9 | The MCC to be used for this network. Default is 1. |
||
| 10 | |||
| 11 | ==== mobile network code ==== |
||
| 12 | |||
| 13 | The MNC to be used for this network. Default is 1. |
||
| 14 | |||
| 15 | ==== short name ==== |
||
| 16 | |||
| 17 | This is the short network name to be used in the GSM 04.08 MM INFO message. |
||
| 18 | |||
| 19 | ==== long name ==== |
||
| 20 | |||
| 21 | This is the long network name to be used in the GSM 04.08 MM INFO message. |
||
| 22 | |||
| 23 | ==== auth policy ==== |
||
| 24 | |||
| 25 | This defines the authentication policy of the network. Possible values are: |
||
| 26 | |||
| 27 | * ''closed'': Don't allow anyone who is not marked as authorized=1 in the hlr database |
||
| 28 | * ''accept-all': Accept everyone into the network |
||
| 29 | * ''token'': Use a special [wiki:TokenAuthPolicy] |
||
| 30 | |||
| 31 | === bts level === |
||
| 32 | |||
| 33 | ==== type ==== |
||
| 34 | |||
| 35 | The type of the BTS. Currently supported; |
||
| 36 | |||
| 37 | * ''bs-11'' |
||
| 38 | * ''nanobts900'' |
||
| 39 | * ''nanobts1800'' |
||
| 40 | |||
| 41 | ==== band ==== |
||
| 42 | |||
| 43 | The GSM band of the BTS. Currently supported: |
||
| 44 | |||
| 45 | * |
||
| 46 | |||
| 47 | ==== location area code ==== |
||
| 48 | |||
| 49 | The LAC of the location area to which this BTS belongs. |
||
| 50 | |||
| 51 | ==== base station id code ==== |
||
| 52 | |||
| 53 | The BSIC of this BTS within the location area. |
||
| 54 | |||
| 55 | ==== ms max power ==== |
||
| 56 | |||
| 57 | maximum transmit power (in dBm) to be used by MS in this BTS |
||
| 58 | |||
| 59 | ==== periodic location update ==== |
||
| 60 | |||
| 61 | Specify the number of seconds at which periodic location updating shall be performed by MS in this BTS (T3212) |
||
| 62 | |||
| 63 | ==== channel allocator ==== |
||
| 64 | |||
| 65 | Whether the channels should be allocated in ascending or descending order |
||
| 66 | |||
| 67 | ==== cell barred ==== |
||
| 68 | |||
| 69 | Whether this BTS is barred from access or not. |
||
| 70 | |||
| 71 | ==== ip.access unit_id ==== |
||
| 72 | |||
| 73 | The ip.access Unit ID. Unit ID is used to identify the BTS to the BSC. You set the Unit ID of the BTS by using the [wiki:ipaccess-config] program. Make sure you use the same Unit ID in the nanoBTS as well as in OpenBSC. |
||
| 74 | |||
| 75 | ==== oml e1 tei ==== |
||
| 76 | |||
| 77 | The Q.921 TEI to be used for the A-bis OML link of this BTS. Make sure you use the same value than you have set in the BTS. |
