DUG 20 » History » Version 12
laforge, 03/26/2021 09:46 AM
1 | 1 | laforge | h1. DUG 20 |
---|---|---|---|
2 | |||
3 | 2 | laforge | This is the second-generation GSM Digital Unit for RBS 6xxx. It combines the baseband processing and back-haul interface of up to 12 TRX, in 1..6 logical BTSs. |
4 | 1 | laforge | |
5 | 2 | laforge | The DUG 20 is only compatible with the [[RUS]] and [[RRUS]] radio units, not with the older [[RUG]] units. |
6 | |||
7 | 3 | roh | {{thumbnail(DUG20_01_front_complete.jpg, size=900)}} |
8 | |||
9 | 4 | roh | {{>toc}} |
10 | |||
11 | 2 | laforge | h2. Technical data |
12 | |||
13 | * 48V DC supply power |
||
14 | * 70W maximal power consumption |
||
15 | * Size: 8U x 31mm x 250mm |
||
16 | * Weight: < 2kg |
||
17 | |||
18 | 7 | laforge | h2. Flash |
19 | 2 | laforge | |
20 | 7 | laforge | There is a CF slot on the left this device and it holds a 256mbyte CF card. The card contains a FAT filesystem with both the software as well as the configuration (IDB = Installatin DataBase). |
21 | 1 | laforge | |
22 | 7 | laforge | {{thumbnail(DUG20_01_CF-slot_detail.jpg, size=400)}} |
23 | 1 | laforge | |
24 | 7 | laforge | h2. Connections |
25 | 2 | laforge | |
26 | 7 | laforge | h3. Front Haul |
27 | 2 | laforge | |
28 | 7 | laforge | The DUG 20 has 6 SFP slots for the interface towards the radio units, labelled RI A..F |
29 | 3 | roh | |
30 | 7 | laforge | {{thumbnail(DUG20_01_SFP_1_detail.jpg, size=400)}} |
31 | {{thumbnail(DUG20_01_SFP_2_detail.jpg, size=400)}} |
||
32 | 3 | roh | |
33 | 7 | laforge | This is where you connect your [[RUS]] or [[RRUS]], either via direct-attach cables (usual for RUS), or via SFP transceivers and optical fiber (usual for RRUS). |
34 | 3 | roh | |
35 | 7 | laforge | h3. Back-Haul interface |
36 | 3 | roh | |
37 | 7 | laforge | The back-haul interface is Classic T1/E1/J1 (ISDN) based. The DUG has four T1/E1/J1 lines exposed as two RJ45 connectors ("ET A" and "ET B") |
38 | 3 | roh | |
39 | 7 | laforge | {{thumbnail(DUG20_01_ETB_ETA_detail.jpg, size=400)}} |
40 | 1 | laforge | |
41 | 11 | tnt | Pinout: |
42 | |||
43 | |_.RJ45|_.Line|_.Signal| |
||
44 | |1|A|RX tip (+)| |
||
45 | |2|A|RX ring (-)| |
||
46 | |3|B|TX tip (+)| |
||
47 | |4|A|TX tip (+)| |
||
48 | |5|A|TX ring (-)| |
||
49 | |6|B|TX ring (-)| |
||
50 | |7|B|RX tip (+)| |
||
51 | |8|B|RX ring (-)| |
||
52 | |||
53 | Same pinout as a Digium card with 2 lines per port. |
||
54 | So a cross-over cable is needed to connect to it. |
||
55 | |||
56 | 1 | laforge | |
57 | h3. ESB port |
||
58 | |||
59 | note that its a bit smaller than the sfp slots |
||
60 | |||
61 | {{thumbnail(DUG20_01_ESB_detail.jpg, size=400)}} |
||
62 | |||
63 | h3. LMT B, LMT A, EC, GPS |
||
64 | |||
65 | {{thumbnail(DUG20_01_LMT_GPS_detail.jpg, size=400)}} |
||
66 | |||
67 | 7 | laforge | h3. LMT A |
68 | |||
69 | LMT (Local Maintenance Terminal) A hosts a RS-232 port used for connecting to the DUG 20 from a PC running the OMT software. |
||
70 | |||
71 | 8 | laforge | |_.RJ45|_.DB-9 (female)|_.Signal| |
72 | |1|5|GND| |
||
73 | |2|3|TxD| |
||
74 | |3|2|RxD| |
||
75 | |||
76 | 1 | laforge | h3. LMT B |
77 | 9 | laforge | |
78 | Site-LAN and LMT B |
||
79 | 7 | laforge | |
80 | FIXME |
||
81 | |||
82 | h3. EC |
||
83 | |||
84 | 10 | laforge | "Enclosure Control". A (likely) RS-485 based site-local bus between different parts, particularly any power supply / climate systems and the digital unit. Used for monitoring/alamrs in case of environmental failure. |
85 | 7 | laforge | |
86 | h3. GPS |
||
87 | |||
88 | This port is meant for attaching an external GPS receiver. The connector includes |
||
89 | * RS485/422 receiver for NMEA from the GPS |
||
90 | * RS485/422 transmitter for command to the GPS |
||
91 | * RS485/422 receiver for 1PPS signal from the GPS |
||
92 | * 12V power supply for the GPS |
||
93 | |||
94 | 1 | laforge | h3. 48V DC in |
95 | |||
96 | Connectory type is a https://www.te.com/usa-en/product-1982299-3.html with associated crimp contacts. |
||
97 | |||
98 | {{thumbnail(DUG20_01_DC_in_detail.jpg, size=400)}} |
||
99 | |||
100 | 7 | laforge | |
101 | 3 | roh | h3. Connector on the Back |
102 | |||
103 | 7 | laforge | This connector is not used during normal operation. We assume it is for factory / service use only. |
104 | |||
105 | 3 | roh | {{thumbnail(DUG20_01_backplane_detail.jpg, size=400)}} |
106 | 7 | laforge | |
107 | |||
108 | h2. LEDs |
||
109 | |||
110 | {{thumbnail(DUG20_01_LED_detail.jpg, size=400)}} |
||
111 | |||
112 | |||
113 | 3 | roh | |
114 | h2. Overview Pictures |
||
115 | |||
116 | {{thumbnail(DUG20_01_front_perspective.jpg, size=400)}} |
||
117 | {{thumbnail(DUG20_01_left_perspective.jpg, size=400)}} |
||
118 | {{thumbnail(DUG20_01_right_perspective.jpg, size=400)}} |
||
119 | {{thumbnail(DUG20_01_back_perspective.jpg, size=400)}} |
||
120 | {{thumbnail(DUG20_01_bottom_complete.jpg, size=400)}} |
||
121 | 12 | laforge | |
122 | h3. Internal pictures |
||
123 | |||
124 | {{thumbnail(dug20_pcba_top.jpg, size=400)}} |
||
125 | {{thumbnail(dug20_pcba_bot.jpg, size=400)}} |
||
126 | {{thumbnail(dug20_pcba_rj45.jpg, size=400)}} |
||
127 | {{thumbnail(dug20_pcba_rs232.jpg, size=400)}} |
||
128 | |||
129 | |||
130 | h2. Spare Parts |
||
131 | |||
132 | * 4-port RJ45 assenmbly including LMT ports: Amphenol RJHSE538004 |
||
133 | * RS232 transceiver of LMT A port: ST3232ECTR |