Siemens GSM-R Cab Radio » History » Version 3
laforge, 01/23/2023 06:35 PM
| 1 | 3 | laforge | {{>toc}} |
|---|---|---|---|
| 2 | 1 | laforge | |
| 3 | 3 | laforge | h1. Siemens GSM-R CAB Radio |
| 4 | |||
| 5 | Osmocom has been provided with two ancient Siemens GSM CAB Radio devices, i.e. the kind of MS installed fixed into a train engine. |
||
| 6 | |||
| 7 | {{thumbnail(20230123_184656.jpg)}} |
||
| 8 | {{thumbnail(20230123_184637.jpg)}} |
||
| 9 | |||
| 10 | |||
| 11 | h2. Sub-Rack Hardware |
||
| 12 | |||
| 13 | {{thumbnail(20230123_184513.jpg)}} |
||
| 14 | |||
| 15 | |||
| 16 | h3. Backplane |
||
| 17 | |||
| 18 | At the back of the sub-rack there's a custom back-plane to interconnect the various modules |
||
| 19 | |||
| 20 | {{thumbnail(20230123_183101.jpg)}} |
||
| 21 | {{thumbnail(20230123_182917.jpg)}} |
||
| 22 | |||
| 23 | h3. High Voltage Power Supply Module |
||
| 24 | |||
| 25 | This is a fully encapsulated, passive cooled, DC/DC converter with |
||
| 26 | * Input voltage 65..150V |
||
| 27 | * Two output voltage rails of 12V / 4A |
||
| 28 | |||
| 29 | |||
| 30 | h3. 12V -> 5V DC/DC converter Module |
||
| 31 | |||
| 32 | This is a circuit board that generates a 5V rail from 12V |
||
| 33 | |||
| 34 | |||
| 35 | h3. GSM Modem Module |
||
| 36 | |||
| 37 | This is a module implementing the actual GSM-R modem. It consts of two circuit boards: One digital and one analog/RF. |
||
| 38 | |||
| 39 | h4. Digital Board |
||
| 40 | |||
| 41 | h4. RF Board |
||
| 42 | |||
| 43 | |||
| 44 | h3. PC/104 embedded PC Module |
||
| 45 | |||
| 46 | This is a carrier board hosting a PC/104 embedded x86 Mainboard. |
||
| 47 | |||
| 48 | h4. Carrier |
||
| 49 | |||
| 50 | h4. PC/104 x86 SBC |
||
| 51 | |||
| 52 | |||
| 53 | h3. I/O board |
||
| 54 | |||
| 55 | This is a board that brings signals from the backplane and frontplane and brings them to connectors towards the main connector panel. |
||
| 56 | |||
| 57 | |||
| 58 | h2. Handset Hardware |
||
| 59 | |||
| 60 | |||
| 61 | |||
| 62 | 1 | laforge | h2. Connector pinout |
| 63 | 2 | laforge | |
| 64 | h3. EXT RADIO (DB-15 female) |
||
| 65 | |||
| 66 | h3. SER I/O (DB-25 male) |
||
| 67 | |||
| 68 | h3. HMI 1 (DB-25 female) |
||
| 69 | |||
| 70 | h3. HMI 2 (DB-25 female) |
||
| 71 | |||
| 72 | h3. MVB OUT (DB-9 female) |
||
| 73 | |||
| 74 | h3. MVB IN (DB-9 female) |
||
| 75 | |||
| 76 | h3. ANT (N) |
||
| 77 | |||
| 78 | This a standdard 50-ohms N-type conector to connect to the GSM-R antenna. |
||
| 79 | |||
| 80 | 1 | laforge | h3. PMU (DB-9 male) |
| 81 | 2 | laforge | |
| 82 | 3 | laforge | This connector is forwarded internally to the DB-9 connector on the front of the embedded PC. Probably serial console. |
| 83 | 2 | laforge | |
| 84 | h3. TRAIN POWER AND I/O (circular connector) |
||
| 85 | 1 | laforge | |
| 86 | |_.Pin (ext)|_.Internal Connector|_.Internal Connector Pin|_.Wire color|_.Purpose| |
||
| 87 | |H|PL6|1|rose|| |
||
| 88 | |K|PL6|2|white|| |
||
| 89 | |M|PL6|3|green|| |
||
| 90 | |P|PL6|4|purple|| |
||
| 91 | |S|PL6|5|blue|| |
||
| 92 | |J|PL6|6|black|| |
||
| 93 | |L|PL6|7|red|| |
||
| 94 | |N|PL6|8|yellow|| |
||
| 95 | |R|PL6|9|orange|| |
||
| 96 | |B|PL6|10|green|| |
||
| 97 | |T|PL7|1|white|| |
||
| 98 | |d|PL7|2|green|| |
||
| 99 | |F|PL7|4|blue|| |
||
| 100 | |A|PL7|5|red|| |
||
| 101 | |U|PL7|6|rose|| |
||
| 102 | |e|PL7|7|blue|| |
||
| 103 | |G|PL7|9|grey|| |
||
| 104 | |C|PL7|10|yellow|| |
||
| 105 | |V|PL8|1|white|| |
||
| 106 | |D|PL8|3|purple|| |
||
| 107 | |W|PL8|4|red|| |
||
| 108 | |E|PL8|6|orange|| |
||
| 109 | |c|PL9|1|orange|| |
||
| 110 | |Z|PL9|2|rose|| |
||
| 111 | |X|PL9|3|green|| |
||
| 112 | |b|PL9|4|grey|| |
||
| 113 | |a|PL9|5|red|| |
||
| 114 | |Y|PL9|6|yellow|| |
