OsmoNITB Migration Guide » History » Revision 14
Revision 13 (neels, 10/30/2017 05:51 PM) → Revision 14/26 (lynxis, 11/07/2017 04:22 PM)
{{>toc}} h1. OsmoNITB Migration Guide Historically, Osmocom offered the [[OsmoNITB:]] "Network-In-The-Box" as an actual single program. It was a useful simplification at the time, but in 2017, Osmocom have decided to split OsmoNITB into programs more closely resembling traditional network architecture. It is recommended to use the new separate components instead of the OsmoNITB, since active development focus has moved there. Creating a new Network In The Box from scratch is described at [[Osmocom Network In The Box]], please refer to that page to complement the descriptions found here. This page aims at describing the steps necessary to move from a working operation of osmo-nitb to the new split components. h1. Subscriber Database With OsmoHLR comes *@osmo-hlr-db-tool@*, which is capable of importing the most important subscriber data from a database that was used with OsmoNITB. In a standard installation, the osmo-nitb database should be found at @/var/lib/osmocom/hlr.sqlite3@, and the osmo-hlr database is expected at @/var/lib/osmocom/hlr.db@. Hence the migration command becomes: <pre> osmo-hlr-db-tool --database /var/lib/osmocom/hlr.db import-nitb-db --import-nitb-db /var/lib/osmocom/hlr.sqlite3 </pre> If no @--database@ is passed, @./hlr.db@ is assumed. If the target @hlr.db@ does not exist yet, it is created. If no @--import-nitb-db@ is passed, a @hlr.db@ without any subscriber data is created. You may repeat / combine imports to the same @hlr.db@; any subscribers that already exist will be skipped with an error message. It is possible to do an import while osmo-hlr is actively using the database, but that is not recommended. Take care that the resulting hlr.db has the proper read and write permissions by the user that will run OsmoHLR. Probably, the same ownership and permissions that the previous OsmoNITB database had is the correct choice. Note that not all information is copied to the hlr.db, so far just IMSI, MSISDN and 2G auth tokens are migrated -- check the @osmo-hlr-db-tool@ cmdline help to find out what exactly is migrated at the time you're reading this. To avoid future confusion, it may be desirable to remove the legacy hlr.sqlite3 from the system (i.e. backup to somewhere else), or rename it to something like @osmo-nitb.db@, so that it is not mistaken for the OsmoHLR database. h1. Configuration Files Most of the current OsmoNITB config options still exist, but are now moved to OsmoMSC or OsmoBSC. Few are required in both. New configuration is available to set up: * the GSUP connection from OsmoMSC to the OsmoHLR, and * the SCCP connection for the A-interface between OsmoBSC and OsmoMSC, established via OsmoSTP. Let's take this standard OsmoNITB configuration and split it up in OsmoBSC and OsmoMSC parts: *OsmoNITB config*: <pre> # ---------- to OsmoBSC: e1_input e1_line 0 driver ipa ipa bind 10.42.42.2 # ---------- to both OsmoBSC and OsmoMSC: network network country code 901 mobile network code 70 short name osmo-gsm-tester-nitb long name osmo-gsm-tester-nitb auth policy closed location updating reject cause 13 encryption a5 0 # ---------- to OsmoBSC: neci 1 rrlp mode none mm info 1 handover 0 handover window rxlev averaging 10 handover window rxqual averaging 1 handover window rxlev neighbor averaging 10 handover power budget interval 6 handover power budget hysteresis 3 handover maximum distance 9999 bts 0 type sysmobts band GSM-1800 cell_identity 0 location_area_code 23 training_sequence_code 7 base_station_id_code 63 ms max power 33 cell reselection hysteresis 4 rxlev access min 0 channel allocator ascending rach tx integer 9 rach max transmission 7 ip.access unit_id 1 0 oml ip.access stream_id 255 line 0 gprs mode none trx 0 rf_locked 0 arfcn 868 nominal power 23 max_power_red 0 rsl e1 tei 0 timeslot 0 phys_chan_config CCCH+SDCCH4 timeslot 1 phys_chan_config SDCCH8 timeslot 2 phys_chan_config TCH/F timeslot 3 phys_chan_config TCH/F timeslot 4 phys_chan_config TCH/F timeslot 5 phys_chan_config TCH/F timeslot 6 phys_chan_config TCH/F timeslot 7 phys_chan_config TCH/F # ---------- to OsmoMSC: smpp local-tcp-ip 10.42.42.2 2775 system-id test-nitb policy closed </pre> h2. OsmoBSC config To above snippets from the OsmoNITB config, you may want to add a 'cs7 instance' section to configure the SCCP point codes and connection to the OsmoSTP. Note that if omitted, default values apply. You also need to add an 'msc' section to tell OsmoBSC where to reach the MSC. *additions to OsmoBSC's config*: <pre> cs7 instance 0 point-code 0.0.2 sccp-address msc_remote point-code 0.0.1 msc msc-addr msc_remote </pre> This should give you an OsmoBSC config file like: *OsmoBSC config*: <pre> e1_input e1_line 0 driver ipa ipa bind 10.42.42.5 cs7 instance 1 point-code 0.0.2 sccp-address msc_remote point-code 0.0.1 msc ! 'msc_remote' is an address book entry defined above under 'cs7' msc-addr msc_remote network network country code 901 mobile network code 70 short name osmo-gsm-tester-msc long name osmo-gsm-tester-msc auth policy closed location updating reject cause 13 encryption a5 0 authentication optional neci 1 rrlp mode none mm info 1 handover 0 handover window rxlev averaging 10 handover window rxqual averaging 1 handover window rxlev neighbor averaging 10 handover power budget interval 6 handover power budget hysteresis 3 handover maximum distance 9999 bts 0 type sysmobts band GSM-1800 cell_identity 0 location_area_code 23 training_sequence_code 7 base_station_id_code 63 ms max power 33 cell reselection hysteresis 4 rxlev access min 0 channel allocator ascending rach tx integer 9 rach max transmission 7 ip.access unit_id 1 0 oml ip.access stream_id 255 line 0 gprs mode none trx 0 rf_locked 0 arfcn 868 nominal power 23 max_power_red 0 rsl e1 tei 0 timeslot 0 phys_chan_config CCCH+SDCCH4 timeslot 1 phys_chan_config SDCCH8 timeslot 2 phys_chan_config TCH/F timeslot 3 phys_chan_config TCH/F timeslot 4 phys_chan_config TCH/F timeslot 5 phys_chan_config TCH/F timeslot 6 phys_chan_config TCH/F timeslot 7 phys_chan_config TCH/F </pre> h2. OsmoMSC config To the MSC bits copied from OsmoNITB, you may want to add: * a 'cs7 instance' section to configure the SCCP point codes and connection to the OsmoSTP. Note that if omitted, default values apply. * an 'hlr' section if your OsmoHLR is not running on localhost. * an 'msc' section to indicate where to reach the MGW, if it is not on localhost. <pre> cs7 instance 0 point-code 0.0.1 hlr remote-ip 10.42.42.2 msc mgcpgw remote-ip 10.42.42.3 </pre> This should give you an OsmoMSC config file like: *OsmoMSC config*: <pre> cs7 instance 0 point-code 0.0.1 msc mgcpgw remote-ip 10.42.42.3 hlr remote-ip 10.42.42.2 network network country code 901 mobile network code 70 short name osmo-gsm-tester-msc long name osmo-gsm-tester-msc auth policy closed location updating reject cause 13 encryption a5 0 authentication optional smpp local-tcp-ip 10.42.42.4 2775 system-id test-msc policy closed </pre> h1. Service Files TODO