Actions
Stollmann TA+POC¶
- Table of contents
- Stollmann TA+POC
ISDN Modem/TerminalAdapter.
Multiple hardware revisions exist.
Hardware (Rev3)¶
| Supply Voltage | 5V DC |
| Power Consumption | ~2.1W |
| RS232 Connector | DB9 |
| ISDN Line Connector | RJ45 |
Pictures¶
Label:
TA+POC S/N 101322 HW: V3/8Mbit FW: 5.340 Art. No: 935-51529 Stollmann E+V GmbH
AT-Commands¶
ATI TA+POC OK OK ATI1 64 OK ATI2 OK ATI3 V5.340 OK ATI4 Stollmann E+V GmbH OK ATI5 0-DSS1 OK ATI6 (c) Copyright Stollmann E+V GmbH OK ATI7 OK ATI9 ($STO1004\1234AB89\MODEM\STO1004\TA+POC2E) OK ATI77 BOOT LOADER V1.12 201098 030E-02-00 OK ATI99 POCa000 V5.340 Feb 11 2000 16:45:28 OK
at**help
cm
g711law Analog encoding law
conf
enhanced
save store parameter setting
load load stored parameter set
go exit configurator
exit exit configurator
quit exit configurator
reset force hardware reset
defa setup default parameter
fwload load new firmware
fwstart start new firmware
show display actual parameter
help display all commands
ver display version number
showall display enhanced parameter
date
debloc
remote
rmsn msn for remote access
rsub subaddress for remote access
rpwd password for remote access
racctab display remote access table incoming calls (msn/sub)
racctab1
racctab2
racctab3
racctab4
racctab5
trc
trcdln length of trace buffer entry
trcmsk trace mask
trcon start trace
trcoff stop trace
trcclr clear trace buffer
trcread read trace buffer
trclog log trace buffer
cim
cmds select command interface
rsttim Startup delay timer after reset
rstmsg Startup message after reset
dialci
mode select operation mode
status display status of serial and ISDN interface
acctab display access table incoming calls (msn/sub)
typ
isdn D channel protocol
ptp point to point mode
s0led BRI activation mode
ringtimer ring interval (100ms)
rmmsg indicate remote connection
txfwd data forwarding timer (t=x*50ms)
acctab1 allow incoming call no/sub
acctab2 allow incoming call no/sub
acctab3 allow incoming call no/sub
acctab4 allow incoming call no/sub
acctab5 allow incoming call no/sub
xtab display xtab table (xxx)
xtab1 set X.25 addr, isdnno
xtab2 set X.25 addr, isdnno
xtab3 set X.25 addr, isdnno
xtab4 set X.25 addr, isdnno
xtab5 set X.25 addr, isdnno
catab display hotline table (msn/sub)
catab1
catab2
catab3
atparam
ats2
ats3
ats4
ats5
ats6
ats7
ats91
atopt
atrcs
atrej
s10
send3p
x3param
p001
p002
p003
p004
p005
p006
p007
p008
p009
p010
p011
p012
p013
p014
p015
p016
p017
p018
p019
p020
p021
p022
dial
cau last cause of data call
msn msn = isdnno./subaddr
sub
llc llc incoming and outgoing
hlc hlc incoming and outgoing
bc bc incoming and outgoing
prot B channel protocol
cha charging information
chatol accumulated charging information
ats0 AT: rings to answer
brn network baudrate
bsize frame length, valid range 16...2048
br serial baudrate
dbits databits (7,8)
sbits stopbits (1,2)
prty parity
cdtr DTR control
cdcd DCD control
ccts CTS control
cdsr DSR control
flc flow control
idle data timeout for disconnect
cmlp control multilink PPP
chappwd CHAP password
v25bisout enable/disable connect message from V.25bis
v110llc send V110 LLC
v110flc enable disable V110 flow control
npl ISDN Numbering Plan
bod bandwidth on demand
bodiv bod increase value
bodit bod increase time
boddv bod decrease value
boddt bod decrease time
tdi timer delay incoming
cmds2 Subcommandset
OK
at**mode?
select operation mode
0 - AT-V.110
1 - V.25bis-V.110
2 - X.3-X.25 B
3 - X.3-X.31 D
OK
at**status
Current status information TA+POC
serial line: DTR:on, RTS:on, DSR:on, CTS:on, DCD:off, RI:off
ISDN: L1:up
Dch: Prot:DSS1 State:disconnected, CdPN:, CgPN:, prev error: 0
Bch: Prot:V.110 State:disconnected, CdPN:, CgPN:
OK
at**isdn
0-DSS1
OK
at**isdn?
D channel protocol
0 - DSS1
1 - 1TR6
OK
at**show
cm
g711law: 0-Automatic
remote
rmsn: * rsub: * rpwd:
trc
trcdln: 256 trcmsk: 0000000300020500
cim
cmds: 0-ATcmd
dialci
isdn: 0-DSS1 ptp: 0-P-MP
dial
msn: * sub: * prot: 0-V.110 cha: 1
chatol: 2737 brn: 0-adaptive bsize: 2048 br: 0-adaptive
dbits: 8 sbits: 1 prty: 0-none cdtr: 2-control
cdcd: 1-connected ccts: 1-on cdsr: 0-on flc: 3-RTS/CTS
idle: 0 cmlp: 0 chappwd:
v25bisout: 0 v110llc: 1 v110flc: 1 npl: 80 bod: 0
bodiv: 40 bodit: 30 boddv: 40 boddt: 30 tdi: 0
cmds2: 0
OK
at**showall
cm
g711law: 0-Automatic
remote
rmsn: * rsub: * rpwd:
racctab1: racctab2:
racctab3: racctab4:
racctab5:
trc
trcdln: 256 trcmsk: 0000000300020500
cim
cmds: 0-ATcmd rsttim: 40 rstmsg: 0
dialci
isdn: 0-DSS1 ptp: 0-P-MP s0led: 1 ringtimer: 50 rmmsg: 0
txfwd: 1 acctab1: acctab2:
acctab3: acctab4: acctab5:
xtab1: xtab2:
xtab3: xtab4:
xtab5: catab1:
catab2: catab3:
atparam
ats2: 43 ats3: 13 ats4: 10 ats5: 8 ats6: 3
ats7: 30 ats91: 0 atopt: 25 atrcs: 4 atrej: 0
s10: 0 send3p: 1
x3param
p001: 0 p002: 0 p003: 0 p004: 5 p005: 0
p006: 69 p007: 8 p008: 0 p009: 0 p010: 0
p011: 0 p012: 0 p013: 0 p014: 0 p015: 0
p016: 0 p017: 0 p018: 0 p019: 0 p020: 0
p021: 0 p022: 0
dial
msn: * sub: * llc:
hlc: bc: 8890 prot: 0-V.110 cha: 1
chatol: 2737 ats0: 1 brn: 0-adaptive bsize: 2048
br: 0-adaptive dbits: 8 sbits: 1 prty: 0-none
cdtr: 2-control cdcd: 1-connected ccts: 1-on
cdsr: 0-on flc: 3-RTS/CTS idle: 0 cmlp: 0
chappwd: v25bisout: 0 v110llc: 1
v110flc: 1 npl: 80 bod: 0 bodiv: 40 bodit: 30
boddv: 40 boddt: 30 tdi: 0 cmds2: 0
OK
Updated by roox over 1 year ago · 1 revisions
