Project

General

Profile

Actions

osmo-pcu

A PCU (Packet Control Unit) is one of the two GPRS elements in the BSS. It implements the RLC and MAC layers of the GPRS
Um (radio) interface on the MS-facing side, as well as the Gb Interface (NS,BSSGP) on the SGSN-facing side.

OsmoPCU is the Osmocom implementation of this PCU functionality.

Towards the SGSN, the BSSGP and NS protocols are implemented over UDP/IP, sometimes called "NS over IP".
It has been tested with OsmoSGSN as well as an Ericsson SGSN so far.

OsmoPCU in co-location with OsmoBTS

OsmoPCU is usually used in co-location with OsmoBTS. In this scenario all OsmoBTS variants are supported, including
OsmoTRX and PHY based variants, such as sysmoBTS.

OsmoPCU in co-location with OsmoBSC

OsmoPCU can also be used in co-location with OsmoBSC. This scenario is required to support third party BTSs that
do not include an integrated PCU. This is mainly the case for classic E1 based BTS, such as the ericsson-rbs-6xxx
series.

The support for BSC co-location in OsmoPCU and OsmoBSC, as well as the hardware specific extensions needed to support
Ericsson RBS2000/RBS6000 base stations have been made possible through funding by the
NLnet foundation (see also: https://nlnet.nl/project/Osmocom-RBS/).

Interface between OsmoPCU and OsmoBTS/OsmoBSC

The interface between OsmoPCU and OsmoBTS/OsmoBSC runs over UNIX socket of SOCK_SEQPACKET type. It is used to configure
the network parameters inside the PCU and to exchange signalling information. It also features a custom L1 interface
that allows PDCH MAC blocks. However, for enhanced performance, OsmoPCU also implements a direct PHY acces for some BTS
models.

Documentation

The primitives, which are exchanged between OsmoPCU and OsmoBTS/OsmoBSC are defined in pcuif_proto.h Message flow charts that explain PDCH activation and deactivation can be found in the OsmoBTS Abis Protocol Specification

Debugging

One of the ways of debugging the PCU socket interface would be via socat:

socat -t30 -x -v UNIX-LISTEN:/tmp/pcu_bts.socat,mode=755,type=5 UNIX-CONNECT:/tmp/pcu_bts,type=5

One might even forward it over network:
socat -t30 -x -v UDP-LISTEN:1666,reuseaddr,fork UNIX-CONNECT:/tmp/pcu_bts,type=5
socat -t30 -x -v UNIX-LISTEN:/tmp/pcu_bts.socat,mode=755,type=5 UDP-CONNECT:127.0.0.1:1666

Note: in the examples above OsmoBTS (listening side) uses default /tmp/pcu_bts socket while OsmoPCU (connecting side)
is configured to use /tmp/pcu_bts.socat via pcu-socket /tmp/pcu_bts.socat config option. It's not recommeded to use
outside of TTCN-3 test environment due to amount of traffic over the socket.

Manuals

Source Code

The source code is available from https://gitea.osmocom.org/cellular-infrastructure/osmo-pcu.git

You can browse it online via https://gitea.osmocom.org/cellular-infrastructure/osmo-pcu

Test Suite

We have a TTCN-3 test suite as part of our Titan_TTCN3_Testsuites

Mailing List / Forum

There is a mailing list for (development) discussion regarding the PCU:
You can subscribe to it (or manage your subscription) at http://lists.osmocom.org/cgi-bin/mailman/listinfo/osmocom-net-gprs

Please make sure to read our MailingListRules before posting.

There's now also a 2G RAN category in our discourse forum

Features

osmo-pcu is considered stable and is performing useful service for a number of users, but due to the complexity of GPRS
there is still plenty of area for improvement.

Supported

  • GPRS CS1 to CS4 with dynamic link/rate adaption
  • EDGE MCS1-MCS9 with dynamic link/rate adaption
  • Single-slot and multi-slot operation on downlink
  • Single-slot operation on uplink
  • Independent TFI/USF per PDCH in single-slot allocation mode
  • Automatic or fixed PDCH allocation algorithm selection
  • Delayed release of downlink TBF
  • Active queue management for downlink TBF (!CoDel)
  • Initial setting of timing advance based on RACH
  • BSSGP BVC flow control support
  • Using pchan types of TCH/F_TCH/H_PDCH or TCH/F_PDCH, OsmoBTS supports
    dynamic PDCH/TCH switching (implemented entirely in osmo-bts)
  • Ericsson RBS2000/RBS6000 support (BSC co-located)

Shortcomings / Limitations / Restrictions

Note: this list may be outdated

  • No GPRS/EGPRS mixed mode (yet)
  • No support for hand-over of any sort yet
  • No support of processing measurement reports
  • No timing advance loop, i.e. radial movement is limited
  • No support for power control
  • No Packet Access Reject message on congestion, access is just ignored
  • No PCCCH support
  • Only "Dynamic allocation RLC data block transfer" is supported
  • No network controlled measurement/cell reselection order supported
  • No PTCCH support
  • No support for Packet Flow Contexts (PFC)
  • No support for MS or PFC flow control
  • No support for RLC unacknowledged mode operation
  • No support for MBMS

Authors / Credits

osmo-pcu was originally developed by Ivan Kluchnikov and Andreas Everberg.

Today it is maintaned by Sysmocom.

Commercial Support

Commercial support as well as development, system integration and training services for this project are available from sysmocom

Files (3)
osmo-pcu-0.1.tar.bz2 osmo-pcu-0.1.tar.bz2 350 KB release version 0.1 of osmo-pcu laforge, 01/17/2013 11:37 AM
pcu-edge-osmocom-org.pcap.bz2 pcu-edge-osmocom-org.pcap.bz2 243 KB First internet access through osmo-pcu using EDGE , 02/04/2016 05:30 PM
egprs-gsmtap-dissector.patch egprs-gsmtap-dissector.patch 6.48 KB WIP patch to add EDGE decoding for RLC frames contained in GSMTAP. , 02/04/2016 05:50 PM

Updated by laforge 5 months ago ยท 32 revisions

Add picture from clipboard (Maximum size: 48.8 MB)