Osmo-gbproxy VTY » History » Revision 2
Revision 1 (laforge, 02/19/2016 10:48 PM) → Revision 2/5 (laforge, 02/19/2016 10:48 PM)
{{>toc}} [[PageOutline]] This page is a reference fo all VTY commands that you can use interactively on the osmo-gbproxy VTY telnet interface on TCP port 4246 In addition, the same commands are used for the configuration file. h2. == configuration reference h3. == === gbproxy level h4. === ==== nsip sgsn remote ip A.B.C.D ==== Set the remote IP address for the connection to the SGSN. h4. ==== nsip sgsn remote port <0-65534> ==== Set the remote UDP port for the connection to the SGSN. h4. ==== nsip sgsn nsei <0-65534> ==== Set the NSEI for the connection to the SGSN. h4. ==== nsip sgsn nsvci <0-65534> ==== Set the NS-VCI for the connection to the SGSN. h3. === ns level h4. === ==== timer (tns-block|tns-block-retries|tns-reset|tns-reset-retries|tns-test|tns-alive|tns-alive-retries) <0-65535> ==== Set the respective NS (GSM TS 08.16) timer to the corresponding value (in seconds): * tns-block -- Timer between NS-BLOCK attempts without any NS-BLOCK-ACK response * tns-block-retries -- How often to retransmit an unacknowledged NS-BLOCK * tns-reset -- Timer between NS-RESET attempts without any NS-RESET-ACK response * tns-reset-retries -- How many times should we retry to send NS-RESET * tns-test -- How many seconds to wait for the response to a TEST procedure * tns-alive -- How many seconds to wait for an answer to the ALIVE procedure * tns-alive-retries -- How often should we retry the ALIVE precedure before declaring the link DEAD h4. ==== nse <0-65535> nsvci <0-65534> ==== Configure a persistent NS-VC with a given NSEI and NSVCI h4. ==== nse <0-65535> remote-ip A.B.C.D ==== Set the remote IP address for a persistent NS-VC h4. ==== nse <0-65535> remote-port <0-65535> ==== Set the remote UDP port for a persistent NS-VC h4. ==== nse <0-65535> remote-role (sgsn|bss) ==== Set whether the remote end of the specified persistent NS-VC is a BSS or SGSN. h4. ==== no nse <0-65535> ==== Remove the persistent configuration for the specified NSE h2. == runtime commands h3. == === show ns [stats] === Show a list of all existing NS-VCs <pre> {{{ proxy.osmocom.org> show ns NSEI 2342, NS-VC 2342, Remote: BSS , DEAD BLOCKED, 192.161.252.121:23000 NSEI 8989, NS-VC 8989, Remote: SGSN, ALIVE UNBLOCKED, 192.181.57.10:23000 </pre> }}} If the stats parameter is given, statistics will be included. h3. === show ns (nsei|nsvc) <0-65535> [stats] === Show information for one specific NS-VC identified by NSVCI or NSEI, optionally including stats <pre> {{{ proxy.osmocom.org> show ns nsei 2342 stats NSEI 2342, NS-VC 2342, Remote: BSS , DEAD BLOCKED, 192.161.252.121:23000 NSVC Peer Statistics: Packets at NS Level ( In): 402 (0/s 0/m 0/h 402/d) Packets at NS Level (Out): 253 (0/s 0/m 0/h 253/d) Bytes at NS Level ( In): 3787 (0/s 0/m 0/h 3787/d) Bytes at NS Level (Out): 269 (0/s 0/m 0/h 269/d) NS-VC Block count : 1 (0/s 0/m 0/h 1/d) NS-VC gone dead count : 1 (0/s 0/m 0/h 1/d) </pre> h3. }}} === logging filter nsvc (nsei|nsvci) <0-65535> === Set a logging filter, i.e. only display log messages related to the specified NSEI / NSVCI
