Project

General

Profile

Actions

SDR OsmoTRX network from scratch » History » Revision 7

« Previous | Revision 7/48 (diff) | Next »
jolly, 02/19/2016 10:47 PM


PageOutline = Installing a GSM network from scratch =

This document describes how to install, configure and run BTS transceiver, OsmoBTS, OpenBSC and LCR.

In order to use this quick howto, you must have basic knowledge about GIT and be familiar with compiling packages from source.

Prerequisite

=== opencore-amr ===

This package installs GSM adaptive multirate codecs

It can downloaded at [http://sourceforge.net/projects/opencore-amr/files/opencore-amr/]

{{{
tar xvzf opencore-amr-x.x.x.tar.gz
cd opencore-amr-x.x.x
./configure
make
make install
ldconfig
cd ..
}}}

=== Sip-Sofia ===

This package installs the open source SIP stack of Nokia Research Center.

It can downloaded at [http://sourceforge.net/projects/sofia-sip/files/sofia-sip/].

{{{
tar xvzf sofia-sip-x.xx.xx.tar.gz
cd sofia-sip-x.xx.xx
./configure
make
make install
ldconfig
cd ..
}}}

=== oRTP ===

This package installs the open source RTP protocol required for libosmo-abis.

It can downloaded at [http://download.savannah.gnu.org/releases/linphone/ortp/sources/].

{{{
tar xvzf ortp-x.xx.x.tar.gz
cd ortp-x.xx.x
./configure
make
make install
ldconfig
cd ..
}}}

=== others ===

sqlite3 and libdbi should be available from your distribution.

Installing

=== Linux-Call-Router (LCR) ===

This package installs the open source PBX software to bridge ISDN (DSS1) / SIP / GSM (MNCC protocol)

The latest version can downloaded via git: {{{
git clone git://git.misdn.eu/lcr.git/
}}}

Now configure, as described here:

{{{
cd lcr
autoreconf -i
./configure --with-sip --with-gsm-bs --with-gsm-ms --enable-gsm-hr
}}}

Sometimes it is necessary to point to different pkgconfig path, because your distribution may use other pkgconfig path than the default path of the packages above. Use the following prefix: {{{
PKG_CONFIG_PATH=/usr/local/lib/pkgconfig/ ./configure .....
}}}

The configure result should include: {{{
configure: Compiled with GSM network side support
configure: Compiled with GSM mobile side support
configure: Compiled with GSM half rate codec support
configure: Compiled with GSM AMR codec support
configure: Compiled with SIP support
}}}

Finish the installation: {{{
make
make install
ldconfig
cd ..
}}}

=== libosmocore ===

This package installs the core utility library for various Osmocom projects.

The latest version can downloaded via git: {{{
git clone git://git.osmocom.org/libosmocore.git
}}}

Finish the installation: {{{
cd libosmocore
git checkout -b
autoreconf -i
./configure
make
make install
ldconfig
cd ..
}}}

=== libosmo-abis ===

This package installs the core utility library for various Osmocom projects.

The latest version can downloaded via git: {{{
git clone git://git.osmocom.org/libosmo-abis.git
}}}

Sometimes it is necessary to point to different pkgconfig path, because your distribution may use other pkgconfig path than the default path of the packages above. Use the following prefix: {{{
PKG_CONFIG_PATH=/usr/local/lib/pkgconfig/ ./configure .....
}}}

Finish the installation: {{{
cd libosmo-abis
autoreconf -i
./configure
(sometimes it is necessary to point to different .../lib/pkgconfig/ path: PKG_CONFIG_PATH=/usr/local/lib/pkgconfig/ ./configure .....)
make
make install
ldconfig
cd ..
}}}

=== OpenBSC ===

This package installs the open source base station controller.

The latest version can downloaded via git: {{{
git clone git://git.osmocom.org/openbsc.git
}}}

Finish the installation: {{{
cd openbsc/openbsc/
change repository: git checkout -b jolly/testing origin/jolly/testing
autoreconf -i
./configure
(sometimes it is necessary to point to different .../lib/pkgconfig/ path: PKG_CONFIG_PATH=/usr/local/lib/pkgconfig/ ./configure .....)
make
make install
cd ../..
}}}

=== OsmoBTS ===

osmo-bts: (BTS software)

This package installs the open source base transceiver station.

The latest version can downloaded via git: {{{
git clone git://git.osmocom.org/osmo-bts.git
}}}

Finish the installation: {{{
cd osmo-bts
change repository: git checkout -b jolly/trx origin/jolly/trx
autoreconf -i
./configure --enable-trx
(sometimes it is necessary to point to different .../lib/pkgconfig/ path: PKG_CONFIG_PATH=/usr/local/lib/pkgconfig/ ./configure .....)
make
make install
cd ..
}}}

Configuration examples

=== OpenBTS ===

{{{
mkdir ~/.osmocom
edit ~/.osmocom/osmo-bts.cfg
}}}

{{{
bts 0
band DCS1800
ipa unit-id 1801 0
oml remote-ip 127.0.0.1
rtp bind-ip 127.0.0.1
rtp jitter-buffer 0
paging lifetime 0
radio-link-timeout 32
gsmtap-sapi bcch
gsmtap-sapi ccch
gsmtap-sapi rach
gsmtap-sapi agch
gsmtap-sapi pch
gsmtap-sapi sdcch
gsmtap-sapi pacch
gsmtap-sapi pdtch
gsmtap-sapi sacch
fn-advance 20
ms-power-loop -10
timing-advance-loop
trx 0
rxgain 0
power 0
}}}

=== OpenBSC ===

{{{
mkdir ~/.osmocom
edit ~/.osmocom/open-bsc.cfg
}}}

'''Be sure to change 'arfcn' to a frequency you have license for!'''

{{{
e1_input
e1_line 0 driver ipa
e1_line 0 port 0
network
network country code 262
mobile network code 42
short name OpenBSC
long name OpenBSC
auth policy accept-all
location updating reject cause 13
encryption a5 0
neci 1
paging any use tch 0
rrlp mode ms-based
mm info 1
handover 0
handover window rxlev averaging 10
handover window rxqual averaging 1
handover window rxlev neighbor averaging 10
handover power budget interval 6
handover power budget hysteresis 3
handover maximum distance 9999
timer t3101 10
timer t3103 0
timer t3105 0
timer t3107 0
timer t3109 0
timer t3111 0
timer t3113 60
timer t3115 0
timer t3117 0
timer t3119 0
timer t3122 10
timer t3141 0
dtx-used 0
subscriber-keep-in-ram 0
bts 0
type nanobts
band DCS1800
cell_identity 0
location_area_code 1
training_sequence_code 7
base_station_id_code 63
ms max power 0
cell reselection hysteresis 4
rxlev access min 0
periodic location update 30
channel allocator descending
rach tx integer 9
rach max transmission 7
channel-descrption attach 1
channel-descrption bs-pa-mfrms 5
channel-descrption bs-ag-blks-res 1
ip.access unit_id 1801 0
oml ip.access stream_id 255 line 0
neighbor-list mode automatic
trx 0
rf_locked 0
arfcn 869
nominal power 0
max_power_red 0
rsl e1 tei 0
timeslot 0
phys_chan_config CCCH+SDCCH4
hopping enabled 0
timeslot 1
phys_chan_config TCH/F
hopping enabled 0
timeslot 2
phys_chan_config TCH/F
hopping enabled 0
timeslot 3
phys_chan_config TCH/F
hopping enabled 0
timeslot 4
phys_chan_config TCH/F
hopping enabled 0
timeslot 5
phys_chan_config TCH/F
hopping enabled 0
timeslot 6
phys_chan_config TCH/F
hopping enabled 0
timeslot 7
phys_chan_config TCH/F
hopping enabled 0
}}}

=== LCR ===

==== interface.conf ====

The simplest configuration uses only the GSM interface. It allows LCR to forward calls from GSM to GSM or from GSM to a call test feature.

{{{
edit /usr/local/etc/lcr/interface.conf
}}}

You can remove (or comment out) everything and just add this interface:

{{{
[gsm]
gsm-bs
tones yes
earlyb no
extern
}}}

==== routing.conf ====

{{{
edit /usr/local/etc/lcr/routing.conf
}}}

You can remove (or comment out) everything and just add these rulesets:

{{{
[main]
interface=gsm : goto ruleset=gsm
: disconnect cause=31

[gsm]
dialing=99 : test
: extern interfaces=gsm
}}}

Look at the main rule set. All calls from interface 'gsm' are forwarded to rule set 'gsm'.

Look at the gsm rule set. All calls that dial '99' prefix, will be test calls. All other calls will be forwarded back to 'gsm' interface.

Running

I suggest to have one shell for every process to run, rather than stating all processes as damon from one shell. Not starting as deamon allows to easily see the debugging output.

=== OpenBSC ===

Open a shell and start OpenBSC:

{{{
osmo-nitb -c ~/.osmocom/open-bsc.cfg -l ~/.osmocom/hlr.sqlite3 -P -m
}}}

OpenBSC runs as a stand-alone network with given config file and data base. It allows forwarding of RTP data and connection to LCR, if the options above are used.

{{{
<0005> bsc_init.c:422
WARNING: You are running an 'accept-all' network on a BTS that is not barred. This configuration is likely to interfere with production GSM networks and should only be used in a RF shielded environment such as a faraday cage!

<0019> input/ipaccess.c:925 enabling ipaccess BSC mode
DB: Database initialized.
DB: Database prepared.
<001d> sms_queue.c:220 Attempting to send 20 SMS
}}}

=== OsmoBTS ===

Open a shell and start OsmoBTS:

{{{
osmobts-trx -c ~/.osmocom/osmo-bts.cfg
}}}

{{{
((*)) |
/ \ OsmoBTS
Using MAC address of eth0: 'xx:xx:xx:xx:xx:xx'
...
<000a> trx_if.c:176 No response from tranceiver
<000a> trx_if.c:176 No response from tranceiver
<000a> trx_if.c:176 No response from tranceiver
}}}

=== Transceiver ===

Now start your OpenBTS transceiver.

==== UmTRX ====

The installation/setup/calibration of UmTRX is beyond the scope of this document. Please refer to:

==== calypso-BTS ====

TBD

=== LCR ===

Run LCR with debugging output.

{{{
lcr start
}}}

{{{
  • LCR Version 1.14

LCR 1.14 started, waiting for calls...
}}}

Test call
Files (0)

Updated by jolly about 8 years ago · 7 revisions

Add picture from clipboard (Maximum size: 48.8 MB)