OpenBSC GPRS » History » Revision 3
Revision 2 (tnt, 02/19/2016 10:47 PM) → Revision 3/37 (tnt, 02/19/2016 10:47 PM)
[[PageOutline]]
= OpenBSC GPRS/EDGE Setup page =
== Pre-requisites ==
* A nano BTS with GPRS or EDGE support. BS-11 are not supported (yet?)
* A compiled GGSN from OpenGGSN ( http://sourceforge.net/projects/ggsn/ )
* A working and up-to-date OpenBSC (see [wiki:Building_OpenBSC])
* You will need to (re-)build it after having installed OpenGGSN so that the `libgtp` libgtp is detected and the SGSN binary `osmo-sgsn` osmo-sgsn built.
== Setup ==
First a little picture to illustrate the different elements and their interactions :
[[Image(gprs.png)]]
=== OpenBSC configuration ===
The first step is to configure OpenBSC for gprs support. Add this to the `network/bts` node in `openbsc.cfg`: {{{
phys_chan_config PDCH
}}}
{{{
gprs mode gprs
gprs routing area 0
gprs cell bvci 2
gprs nsei 101
gprs nsvc 0 nsvci 101
gprs nsvc 0 local udp port 23000
gprs nsvc 0 remote udp port 23000
gprs nsvc 0 remote ip 192.168.0.128
}}}
The `gprs nsvc 0 remote` entries `192.168.0.128:23000` is the IP/port of the machine running the SGSN as seen from the BTS. It will be sent by OpenBSC to the BTS in the configration phase and the BTS will connect back to the SGSN.
The second step is to allocate some timeslots to packet data. For this, just change the 1 or more `network/bts/trx/timeslot` nodes using :
{{{
phys_chan_config PDCH
}}}
=== Osmocom SGSN configuration ===
{{{
!
! Osmocom SGSN configuration
!
!
line vty
no login
!
sgsn
gtp local-ip 192.168.1.128
ggsn 0 remote-ip 192.168.1.129
ggsn 0 gtp-version 1
!
ns
timer tns-block 3
timer tns-block-retries 3
timer tns-reset 3
timer tns-reset-retries 3
timer tns-test 30
timer tns-alive 3
timer tns-alive-retries 10
encapsulation udp local-ip 192.168.0.128
encapsulation udp local-port 23000
encapsulation framerelay-gre enabled 0
!
bssgp
!
}}}
=== OpenGGSN configuration ===
{{{
# TAG: listen
# Specifies the local IP address to listen to
listen 192.168.1.129
}}}
{{{
# TAG: dynip
# Dynamic IP address pool.
# Used for allocation of dynamic IP address when address is not given
# by HLR.
# If this option is not given then the net option is used as a substitute.
dynip 192.168.254.0/24
# TAG: pcodns1/pcodns2
# Protocol configuration option domain name system server 1 & 2.
pcodns1 208.67.222.222
pcodns2 208.67.220.220
}}}
=== Network configuration ===
You will also need to configure some networking rules to allow connectivity from `tun0`. Look up linux networking/nat howtos on google.
The basic setup for testing only in a safe environment would be :
{{{
bash# echo 1 > /proc/sys/net/ipv4/ip_forward
bash# iptables -A POSTROUTING -s 192.168.254.0/24 -t nat -o eth0 -j MASQUERADE
}}}
(replace `eth0` by the interface providing your machine connectivity)
== Running ==
# FIXME
