Actions
- Table of contents
- Mikrotik R11e-4G
Mikrotik R11e-4G¶
This is a CAT4 LTE modem in mPCIe form factor based around the Altair ALT3800 baseband chipset and the ALT6300 RF transceiver.
Pictures¶
Console / Boot¶
Boot log¶
NAND read: device 0 offset 0x5a00000, size 0x400000 4194304 bytes read: OK device 0 offset 0x0, size 0x20 32 bytes read: OK partition changed to nand0,5 Scanning JFFS2 FS: ...... done. find_inode failed for name=prop load: Failed to find inode ### JFFS2 LOAD ERROR<0> for /bsp/prop! find_inode failed for name=iosysbp load: Failed to find inode ### JFFS2 LOAD ERROR<0> for /bsp/iosysbp! >>>> bootfw: wakeUpLTE at 0xa039604c >>>> bootfw: wakeUpPHY at 0xa0000488 >>>> bootfw: wakeUpPHY2 at 0xa0069488 Loading from nand0, offset 0x2dc0000 Image Name: ALT3800 Linux Image Type: MIPS Linux Kernel Image (gzip compressed) Data Size: 2256997 Bytes = 2.2 MiB Load Address: 82104000 Entry Point: 8245d920 NAND read: device 0 offset 0x30c0000, size 0x4000 16384 bytes read: OK ## Booting kernel from Legacy Image at 82800000 ... Image Name: ALT3800 Linux Image Type: MIPS Linux Kernel Image (gzip compressed) Data Size: 2256997 Bytes = 2.2 MiB Load Address: 82104000 Entry Point: 8245d920 Verifying Checksum ... OK ## Flattened Device Tree blob at 84000000 Booting using the fdt blob at 0x84000000 Uncompressing Kernel Image ... OK Loading Device Tree to 82ff9000, end 82fff5ab ... OK Building mtd parts altair,alt3800_nfc for device type 2
u-boot environment¶
baudrate=115200
boot_default=run flash_boot
boot_nand_mtd=run nand_choose_rootfs; run flash_set_bootargs; nboot kernel${boot_number}; nand read ${dtb_addr} dtb${boot_number} ${dtb_size}; bootm ${loadaddr} - ${dtb_addr}
boot_nand_ramfs=run ram_set_bootargs; nboot kernel${boot_number}; bootm
boot_number=2
boot_option=boot_default
boot_tftp_ramfs=run ram_set_bootargs; ${tftpbootcmd} vmlinux.uboot; bootm ${loadaddr}
bootcmd=if itest.b 0 == *a00d001b; then run ${boot_option}; else echo 'GUESS MODE - NO BOOT ALLOWED !!!'; fi
bootdelay=6
bootm_low=0x82100000
bootm_size=0x6000000
cdc_connect_timeout=10
consoledev=ttyS0
dtb_addr=0x84000000
dtb_file=alt3802.dtb
dtb_size=0x4000
env_check=if test ${env_saved} = 0; then setenv env_saved 1; saveenv; fi
env_configured_size=0x4000
env_saved=1
erase_env_nand=nand erase.part env; nand erase.part backup_env
eth_phy_mode=rmii
ethact=usb_ether
ethaddr=00:E0:0C:00:95:02
fastboot=setenv loadaddr ${fastboot_loadaddr};run loadfw; if test $? -eq 0; then bootfw ${unziped_fwaddr} 1; fi; run loadotp; if run loadbsp;then run process_fw; fi;
fastboot_loadaddr=0x82800000
fdt_high=0x83000000
fdtdbg=no
flash_boot=run nand_choose_rootfs; run flash_set_bootargs; run fastboot; nboot kernel${boot_number}; nand read ${dtb_addr} dtb${boot_number} ${dtb_size}; bootm ${loadaddr} - ${dtb_addr}
flash_set_bootargs=setenv bootargs $ip root=${root} rw rootfstype=jffs2 console=$consoledev,$kernel_baudrate $othbootargs $kernellog
gatewayip=0.0.0.0
hostname=alt3800
initrd_high=0x83000000
ipaddr=10.0.0.1
kernel_baudrate=115200
kernel_file=uImage
kernellog=quiet
load_fw=run load_phy_fw; run load_lte_fw
load_lte_fw=${tftpbootcmd} $lte_fw; setenv fw_type LTE; bootelf
load_phy_fw=${tftpbootcmd} $phy_fw; setenv fw_type PHY; bootelf
loadaddr=0x80100000
loadbsp=chpart nvm; fsloadbsp 1 ${ramFilesShAddr} band_list bandbp file_list bspfilesbp
loadfw= nand read.jffs2 ${loadaddr} modem_fw${boot_number}; unlzo ${loadaddr} ${unziped_fwaddr};
loadotp=nandotp read ${ramOtpShAddr} spl 20
lte_fw=PS100_RealPHY.elf
mtdparts=mtdparts=alt3800_nfc:512k(spl),768k(uboot1),768k(uboot2),256k(env),256k(backup_env),3m(nvm),3m(kernel1),256k(dtb1),37m(rootfs1),3m(kernel2),256k(dtb2),37m(rootfs2),4m(modem_fw1),4m(modem_fw2),-(tstorage)
nand128_mtdparts=mtdparts=alt3800_nfc:512k(spl),768k(uboot1),768k(uboot2),256k(env),256k(backup_env),3m(nvm),3m(kernel1),256k(dtb1),37m(rootfs1),3m(kernel2),256k(dtb2),37m(rootfs2),4m(modem_fw1),4m(modem_fw2),-(tstorage)
nand128_scheme2_mtdparts=mtdparts=alt3800_nfc:512k(spl),768k(uboot1),768k(uboot2),256k(env),256k(backup_env),3m(nvm),4m(kernel1),256k(dtb1),53m(rootfs1),4m(kernel2),256k(dtb2),53m(rootfs2),4m(modem_fw1),4m(modem_fw2)
nand256_mtdparts=mtdparts=alt3800_nfc:512k(spl),768k(uboot1),768k(uboot2),256k(env),256k(backup_env),3m(nvm),4m(kernel1),256k(dtb1),40m(rootfs1),4m(kernel2),256k(dtb2),40m(rootfs2),4m(modem_fw1),4m(modem_fw2),10m(ua),-(tstorage)
nand_choose_rootfs=if test 1 = ${boot_number}; then setenv root /dev/mtdblock8;else setenv root /dev/mtdblock11; fi
nand_uboot_file=u-boot.bin
nand_uboot_spl_file=u-boot-spl.bin.alt3800
nc=run nchelp; setenv stdin nc;setenv stdout nc;setenv stderr nc
nchelp=echo On the host side run the script: ./netconsole $ipaddr $ncinport
ncinport=6665
ncip=10.0.0.10
ncmux=run nchelp; setenv stdout ${stdout},nc; setenv stdin ${stdin},nc; setenv stderr ${stderr},nc
ncoutport=6665
netdev=eth0
netmask=255.255.0.0
nvm_file=nvm.jffs2.img
phy_dbgstreamer=0
phy_fw=Lte.out
phy_sniffer=0
preboot=run env_check; if test -n $prebootcmd; then echo; echo Running pre-boot command; run prebootcmd;fi;
process_fw=initfw; bootfw ${unziped_fwaddr} 0
ramFilesShAddr=0xA030004c
ramOtpShAddr=0xA0300000
ram_set_bootargs=setenv bootargs $ip root=/dev/ram rw console=$consoledev,$kernel_baudrate $othbootargs $kernellog
rootfs_file=rootfs.jffs2.img
ser=setenv stdin serial;setenv stdout serial;setenv stderr serial
serverip=10.0.0.10
set_ip=setenv ip ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off
stderr=serial,usbtty
stdin=serial,usbtty
stdout=serial,usbtty
testdramaddress=no
testdramcache=yes
testdramcount=1
testdramdata=no
testdramsize=0x08000000
testdramstart=0x80100000
testdramwalk=no
tftpbootcmd=tftpboot
toggle_boot_number=if test 1 = ${boot_number}; then set boot_number 2; else set boot_number 1; fi; saveenv
unziped_fwaddr=0x83000000
update_all=run update_all_nand
update_all_nand=run update_kernel_nand update_dtb_nand update_rootfs_nand
update_dtb=run update_dtb_nand
update_dtb_nand=if ${tftpbootcmd} ${dtb_file}; then nand erase.part dtb${boot_number}; nand write ${loadaddr} dtb${boot_number} ${filesize}; fi
update_kernel=run update_kernel_nand
update_kernel_nand=if ${tftpbootcmd} ${kernel_file}; then nand erase.part kernel${boot_number}; nand write ${loadaddr} kernel${boot_number} ${filesize}; fi
update_linux=${tftpbootcmd} uImage
update_multi_img=run update_multi_img_nand
update_multi_img_nand=setenv kernel_file vmlinux.uboot; run update_kernel_nand
update_nvm=run update_nvm_nand
update_nvm_nand=if ${tftpbootcmd} ${nvm_file}; then nand erase.part nvm; nand write ${loadaddr} nvm ${filesize}; fi
update_ramdisk=${tftpbootcmd} $ramdiskaddr ramdisk.gz.uboot
update_rootfs=run update_rootfs_nand
update_rootfs_nand=if ${tftpbootcmd} ${rootfs_file}; then nand erase.part rootfs${boot_number}; nand write ${loadaddr} rootfs${boot_number} ${filesize}; fi
update_uboot=run update_uboot_nand
update_uboot_nand=run update_uboot_nand_spl update_uboot_nand_non_spl erase_env_nand
update_uboot_nand_non_spl=if ${tftpbootcmd} ${nand_uboot_file}; then nand erase.part uboot1; nand write ${loadaddr} uboot1 ${filesize}; nand erase.part uboot2; nand write ${loadaddr} uboot2 ${filesize}; fi
update_uboot_nand_spl=if ${tftpbootcmd} ${nand_uboot_spl_file}; then nand erase.part spl; nand write ${loadaddr} spl ${filesize}; fi
usbphymode=0
usbtty=cdc_acm
ver=U-Boot 2012.10 (Aug 09 2018 - 10:17:38)
MTD partition layout¶
device nand0 <alt3800_nfc>, # parts = 15 #: name size offset mask_flags 0: spl 0x00080000 0x00000000 0 1: uboot1 0x000c0000 0x00080000 0 2: uboot2 0x000c0000 0x00140000 0 3: env 0x00040000 0x00200000 0 4: backup_env 0x00040000 0x00240000 0 5: nvm 0x00300000 0x00280000 0 6: kernel1 0x00300000 0x00580000 0 7: dtb1 0x00040000 0x00880000 0 8: rootfs1 0x02500000 0x008c0000 0 9: kernel2 0x00300000 0x02dc0000 0 10: dtb2 0x00040000 0x030c0000 0 11: rootfs2 0x02500000 0x03100000 0 12: modem_fw1 0x00400000 0x05600000 0 13: modem_fw2 0x00400000 0x05a00000 0 14: tstorage 0x02200000 0x05e00000 0
Serial Console¶
/dev/ttyS0 of the ALT3800 is exposed on pins of the mPCIe. If you plug the card into an Osmocom mpcie-breakout board, the pins can be easily accessed on a 2.54mm header.
| Function | mPCIe pin | mPCIe name | Breakout JP4 pin |
|---|---|---|---|
| TxD (output) | 3 | COEX1 | 4 |
| RxD (input) | 5 | COEX2 | 3 |
| GND | 4 | GND | 1 |
Please not that the console is not easily usable as the modem appears to permanently go into a deep-power-down mode where UART characters are no longer received. One way to avoid this is by having some program running that keeps interacting with the modem over AT commands.
rootfs¶
/etc/os-release¶
NAME=Buildroot VERSION=2013.11 ID=buildroot VERSION_ID=2013.11 PRETTY_NAME="Buildroot 2013.11"
/proc/cpuinfo¶
system type : altair,ALT3800 processor : 0 cpu model : MIPS 34Kc V5.8 BogoMIPS : 264.19 wait instruction : yes microsecond timers : yes tlb_entries : 64 extra interrupt vector : yes hardware watchpoint : yes, count: 4, address/irw mask: [0x0000, 0x0448, 0x0560, 0x0768] ASEs implemented : mips16 mt shadow register sets : 1 kscratch registers : 0 core : 512 VCED exceptions : not available VCEI exceptions : not available
modules¶
Module Size Used by Tainted: G ebtable_broute 863 1 ebtables 17952 1 ebtable_broute ue_lte 220014 7 g_eth_acm 57031 0
/tmp/printed_routing_tables.txt¶
Normal:
+CNEM to server LTEFW1 (number 5).
+CAVIMS to server LTEFW1 (number 5).
+CGATT to server ECM (number 0).
+CSAS to server SMS (number 3).
%STATCM to server ECM (number 0).
%PCOINFO to server LTEFW1 (number 5).
%CMGSC to server SMS (number 3).
+GMR to server CFG (number 11).
%FLTSMS to server SMS (number 3).
%DBGSTRM to server LTEFW1 (number 5).
H0 to server MOIP (number 10).
%CATAPI to server CAT (number 12).
+CRSM to server LTEFW1 (number 5).
+CIMI to server LTEFW1 (number 5).
%DRCMD to server LTEFW1 (number 5).
+CSCS to server SMS (number 3).
%OMACMD to server VDMC (number 4).
%CEN to server LTEFW1 (number 5).
%DREV to server LTEFW1 (number 5).
%CGINFO to server ECM (number 0).
%AUTH to server LTEFW1 (number 5).
+CMGF to server SMS (number 3).
%GETACFG to server CFG (number 11).
+CEN to server LTEFW1 (number 5).
+CMTLR to server ELC (number 1).
+CLCC to server MOIP (number 10).
%CMGW to server SMS (number 3).
%TIMEREV to server LTEFW1 (number 5).
+CMUT to server MOIP (number 10).
+CMGW to server SMS (number 3).
%PDNRDP to server ECM (number 0).
%GPSTST to server ELC (number 1).
+CMGD to server SMS (number 3).
%SCACHECMD to server LTEFW1 (number 5).
+CUSATA to server CAT (number 12).
+CGDSCONT to server ECM (number 0).
%SMSINFO to server SMS (number 3).
%MOIPAPI to server MOIP (number 10).
%GNSSLOC to server LTEFW1 (number 5).
+CLIR to server MOIP (number 10).
%RESETCID to server LTEFW1 (number 5).
+CSSN to server MOIP (number 10).
%CPININFO to server LTEFW1 (number 5).
+CGCONTRDP to server LTEFW1 (number 5).
%MEAS to server LTEFW1 (number 5).
%OMADMAPI to server VDMC (number 4).
%GETLOG to server LTEFW1 (number 5).
%FOTAEV to server VDMC (number 4).
+CEREG to server LTEFW1 (number 5).
E to server (number 99). entered in the early configuration.
%PCONI to server LTEFW1 (number 5).
%CMGS to server SMS (number 3).
H to server MOIP (number 10).
%SETOTP to server CFG (number 11).
+CMGS to server SMS (number 3).
%LBSCMD to server LTEFW1 (number 5).
%IMSTST to server IMS (number 7).
%GPSCMD to server ELC (number 1).
+GMI to server CFG (number 11).
%CSQ to server LTEFW1 (number 5).
%TSTUSIMSE to server LTEFW1 (number 5).
Z to server ECM (number 0).
+CSQ to server LTEFW1 (number 5).
%LWM2MCMD to server LWM2M (number 2).
+CGSN to server LTEFW1 (number 5).
+GSN to server LTEFW1 (number 5).
+CCHO to server LTEFW1 (number 5).
+CUSATR to server LTEFW1 (number 5).
%GPSINFO to server ELC (number 1).
+COPS to server ECM (number 0).
%PPPCFG to server LTEFW1 (number 5).
%SETCFG to server CFG (number 11).
+CEMODE to server ECM (number 0).
+CNMI to server SMS (number 3).
%DEVINFO to server CFG (number 11).
%VER to server ECM (number 0).
+VZWAPNE to server ECM (number 0).
+CSMS to server SMS (number 3).
+GMM to server CFG (number 11).
%CBARR to server XCAP (number 9).
%CSDH to server SMS (number 3).
+CEUS to server ECM (number 0).
+CPMS to server SMS (number 3).
+CGEREP to server LTEFW1 (number 5).
%EMGNUM to server ECM (number 0).
%EMGCBM to server ECM (number 0).
+CSIM to server LTEFW1 (number 5).
+CPNER to server LTEFW1 (number 5).
%LOGSTOHOST to server CFG (number 11).
+CUSATD to server LTEFW1 (number 5).
+CGCMOD to server LTEFW2 (number 6).
%CEER to server LTEFW1 (number 5).
+CMEE to server LTEFW1 (number 5).
+VTS to server MOIP (number 10).
%SUPLPDNACTEV to server ECM (number 0).
%APNN to server ECM (number 0).
+CRES to server SMS (number 3).
+CNUM to server LTEFW1 (number 5).
%SETROUTE to server ECM (number 0).
+CMTLRA to server ELC (number 1).
%SETPCO to server LTEFW1 (number 5).
%LWM2MEV to server LWM2M (number 2).
%LWM2MAPI to server LWM2M (number 2).
%SETDHCP to server LTEFW1 (number 5).
+CHLD to server MOIP (number 10).
%CCLK to server LTEFW1 (number 5).
%PPPAUTH to server LTEFW1 (number 5).
+CUSATE to server CAT (number 12).
H1 to server MOIP (number 10).
%OMAEV to server VDMC (number 4).
+CCLK to server LTEFW1 (number 5).
%UPGCMD to server CFG (number 11).
%DBPAPI to server DBP (number 8).
I to server CFG (number 11).
%PDNSET to server ECM (number 0).
%SMMA to server SMS (number 3).
+CCFCU to server XCAP (number 9).
+CSCA to server SMS (number 3).
%USMSF to server SMS (number 3).
+CNMA to server SMS (number 3).
%IMSAPI to server IMS (number 7).
%NETSEL to server ECM (number 0).
%SRVCHANGE to server CFG (number 11).
+CPSMS to server ECM (number 0).
%SETACFG to server CFG (number 11).
+CMSS to server SMS (number 3).
+CSDH to server SMS (number 3).
%CMGRS to server LTEFW1 (number 5).
%CCID to server LTEFW1 (number 5).
%GETID to server LTEFW1 (number 5).
%TSTLTE to server LTEFW1 (number 5).
+CCWA to server MOIP (number 10).
+CCHC to server LTEFW1 (number 5).
%OTPCMD to server CFG (number 11).
+CGMM to server CFG (number 11).
%IMSCMD to server ECM (number 0).
%OTDOACMD to server LTEFW1 (number 5).
%ECMAPI to server ECM (number 0).
%LTECMD to server LTEFW1 (number 5).
%DATACMD to server ECM (number 0).
%GPSEV to server ELC (number 1).
+CGSMS to server SMS (number 3).
+CRLA to server LTEFW1 (number 5).
+CMGC to server SMS (number 3).
%FOTAINFO to server VDMC (number 4).
+CLCK to server LTEFW1 (number 5).
+CFUN to server ECM (number 0).
%SETLOG to server LTEFW1 (number 5).
%CATSTAT to server LTEFW1 (number 5).
%SETBDELAY to server CFG (number 11).
%CSGCMD to server LTEFW2 (number 6).
%SRVLOCK to server CFG (number 11).
%NOTIFYEV to server LTEFW1 (number 5).
+CVHU to server MOIP (number 10).
%TRSHCMD to server LTEFW1 (number 5).
+CGMI to server CFG (number 11).
%LWM2MOPEV to server LWM2M (number 2).
%VLTCMD to server MOIP (number 10).
+CMGR to server SMS (number 3).
+CLIP to server MOIP (number 10).
%STATUS to server LTEFW1 (number 5).
+COLP to server MOIP (number 10).
A to server MOIP (number 10).
+CREG to server LTEFW1 (number 5).
%CEREG to server LTEFW1 (number 5).
%ATUSOLDEL to server LTEFW1 (number 5).
%VECEER to server MOIP (number 10).
%VLTEV to server MOIP (number 10).
+VTD to server MOIP (number 10).
%GETCFG to server LTEFW1 (number 5).
%EMGCMD to server ECM (number 0).
&F0 to server ECM (number 0).
+CTFR to server MOIP (number 10).
+CIREG to server IMS (number 7).
%CATEV to server CAT (number 12).
%DMSES to server VDMC (number 4).
+CPOL to server LTEFW1 (number 5).
+CUSATT to server CAT (number 12).
+CUSATW to server LTEFW1 (number 5).
%EXE to server CFG (number 11).
%CMGWC to server SMS (number 3).
%PDNACT to server ECM (number 0).
%NFSMNG to server CFG (number 11).
%IMSINITEN to server ECM (number 0).
%CNMA to server LTEFW1 (number 5).
%ROHCCMD to server LTEFW1 (number 5).
+CPIN to server LTEFW1 (number 5).
%CATPOLLINT to server LTEFW1 (number 5).
%SIMSTAT to server ECM (number 0).
%COLLECTLOGS to server CFG (number 11).
%TSTEXT to server LTEFW2 (number 6).
%CATLOCINF to server LTEFW1 (number 5).
+CMGL to server SMS (number 3).
%CSMP to server SMS (number 3).
%CGDCONT to server LTEFW1 (number 5).
AT to server LTEFW1 (number 5).
%CMATT to server ECM (number 0).
%FOTACMD to server VDMC (number 4).
+CSMP to server SMS (number 3).
+CDU to server MOIP (number 10).
+CGDCONT to server ECM (number 0).
%LTERR to server LTEFW1 (number 5).
%CHKPLMN to server LTEFW1 (number 5).
+CIREP to server LTEFW1 (number 5).
+CGACT to server ECM (number 0).
%BANDCAP to server CFG (number 11).
%NPEV to server LTEFW1 (number 5).
%SMSAPI to server SMS (number 3).
%COUNT to server LTEFW1 (number 5).
%SETURLIP to server ECM (number 0).
+CGMR to server CFG (number 11).
%SUPLPDNACT to server ECM (number 0).
Exceptions:
+CGATT
from input ECM (number 3) to LTEFW2.
+CFUN
from input ECM (number 3) to LTEFW1.
+CNMI
from input SMS (number 5) to LTEFW1.
%EMGCMD
from input ECM (number 3) to LTEFW1.
%CMGW
from input SMS (number 5) to LTEFW1.
+CGDSCONT
from input ECM (number 3) to LTEFW1.
+CMGW
from input SMS (number 5) to LTEFW1.
%VER
from input ECM (number 3) to LTEFW1.
+CGDCONT
from input ECM (number 3) to LTEFW1.
+COPS
from input ECM (number 3) to LTEFW2.
+CPSMS
from input ECM (number 3) to LTEFW1.
+CMGD
from input SMS (number 5) to LTEFW1.
+CGACT
from input ECM (number 3) to LTEFW2.
%SETCFG
from input CFG (number 39) to LTEFW1.
from input VDMC (number 25) to LTEFW1.
from input ATSCRIPT (number 1) to LTEFW1.
+CMGR
from input SMS (number 5) to LTEFW1.
+CEMODE
from input ECM (number 3) to LTEFW1.
+CNMA
from input SMS (number 5) to LTEFW1.
+CMGL
from input SMS (number 5) to LTEFW1.
%CMGS
from input SMS (number 5) to LTEFW1.
+CMGS
from input SMS (number 5) to LTEFW1.
%SETOTP
from input CFG (number 39) to LTEFW1.
%PWRSVCMD
from input ATSCRIPT (number 1) to CFG.
from input WEBG (number 7) to CFG.
from input HOSTV (number 9) to CFG.
+CUSATA
from input CAT (number 8) to LTEFW1.
+CPMS
from input SMS (number 5) to LTEFW1.
unsolicited:
%MBMSEV to:
MALUNSOL (number 31)
HOSTS (number 0)
HOSTV (number 9)
NO CARRIER to:
SMUN (number 23)
HOSTV (number 9)
+CPNERU to:
HOSTV (number 9)
%STATCM to:
ASPSU (number 46)
MBIMUN (number 33)
FASTSER (number 30)
HOSTV (number 9)
HOSTS (number 0)
%CDS to:
SMSUN (number 4)
%CATSTAT to:
CAT (number 8)
%DREV to:
ECMUN (number 47)
+CEN2 to:
ECMUN (number 47)
%GPSEV to:
TRKU (number 42)
FASTSER (number 30)
HOSTS (number 0)
HOSTV (number 9)
%NPEVU to:
ELCOUT (number 20)
CAT (number 8)
ECMUN (number 47)
+CDS to:
FASTSER (number 30)
HOSTV (number 9)
%CEREGU to:
ELCOUT (number 20)
CAT (number 8)
ECMUN (number 47)
%VLTCMDU to:
SMUN (number 23)
HOSTV (number 9)
%FOTAEV to:
FOTAMUN (number 28)
HOSTV (number 9)
%IMSEV to:
ECMUN (number 47)
CAT (number 8)
%IMSSTATEV to:
ECMUN (number 47)
%OTDOAMEAS to:
ELCOUT (number 20)
%LWM2MOPEV to:
HOSTV (number 9)
%CEER to:
CAT (number 8)
ECMUN (number 47)
+CIREGU to:
SMUN (number 23)
HOSTV (number 9)
%OMAEV to:
FOTAMUN (number 28)
HOSTV (number 9)
+CEREG to:
FASTSER (number 30)
HOSTV (number 9)
HOSTS (number 0)
+CMTLR to:
HOSTS (number 0)
HOSTV (number 9)
+CBM to:
HOSTV (number 9)
+CDSI to:
FASTSER (number 30)
HOSTV (number 9)
%SUPLNIEV to:
ELCOUT (number 20)
+CNEMS1 to:
ECMUN (number 47)
+CDUU to:
SMUN (number 23)
HOSTV (number 9)
+CSSU to:
SMUN (number 23)
HOSTV (number 9)
%CHKPLMN to:
CAT (number 8)
%NOTIFYEV to:
ASPSU (number 46)
MBIMUN (number 33)
HOSTV (number 9)
ECMUN (number 47)
+CUSATEND to:
HOSTV (number 9)
%EMGCBM to:
HOSTV (number 9)
+COLP to:
SMUN (number 23)
HOSTV (number 9)
%CMT to:
SMSUN (number 4)
+CSSI to:
SMUN (number 23)
HOSTV (number 9)
%LWM2MEV to:
FOTAMUN (number 28)
HOSTV (number 9)
+CLIP to:
SMUN (number 23)
HOSTV (number 9)
+CMT to:
FASTSER (number 30)
PWRTSMUN (number 24)
WEBUN (number 17)
MBIMUN (number 33)
HOSTV (number 9)
HOSTS (number 0)
+CREG to:
MBIMUN (number 33)
%SCANEND to:
FASTSER (number 30)
HOSTV (number 9)
HOSTS (number 0)
%GPSUNSOL to:
HOSTS (number 0)
HOSTV (number 9)
%SUPLPDNACTEV to:
ELCOUT (number 20)
RING to:
SMUN (number 23)
HOSTV (number 9)
%LBSCMDU to:
ELCOUT (number 20)
%CATPDNSTAT to:
CAT (number 8)
%VLTEV to:
SMUN (number 23)
HOSTV (number 9)
+CEN1 to:
ECMUN (number 47)
+CUSATP to:
HOSTV (number 9)
+CCWA to:
SMUN (number 23)
HOSTV (number 9)
+CGEV to:
HOSTV (number 9)
ASPSU (number 46)
ECMUN (number 47)
+CMTI to:
TRKU (number 42)
FASTSER (number 30)
PWRTSMUN (number 24)
WEBUN (number 17)
MBIMUN (number 33)
HOSTV (number 9)
HOSTS (number 0)
%LTERRU to:
ECMUN (number 47)
Cancelable:
+CGATT
Dynamic unsolicited configuration:
Network Interfaces¶
root@LTE-GW:/sys/class# ifconfig
br0 Link encap:Ethernet HWaddr 00:11:22:33:44:55
inet addr:198.51.100.100 Bcast:198.51.100.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:463 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:81177 (79.2 KiB) TX bytes:0 (0.0 B)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
lte0 Link encap:Ethernet HWaddr 00:1A:2B:3C:4D:5E
UP MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
usb0 Link encap:Ethernet HWaddr 00:11:22:33:44:55
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:463 errors:0 dropped:0 overruns:0 frame:0
TX packets:17 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:81177 (79.2 KiB) TX bytes:782 (782.0 B)
root@LTE-GW:/sys/class# brctl show
bridge name bridge id STP enabled interfaces
br0 8000.001122334455 no usb0
Further Information¶
Updated by laforge almost 4 years ago · 8 revisions
