Project

General

Profile

SIMtrace Hardware » History » Version 33

laforge, 03/17/2017 07:17 AM

1 31 tsaitgaist
{{>toc}}
2 1 laforge
3 31 tsaitgaist
h1. Osmocom SIMtrace Hardware
4 1 laforge
5 31 tsaitgaist
6
This page is dedicated to the Hardware for Osmocom [[SIMtrace]], which looks like this:
7
8 32 zecke
{{thumbnail(simtrace_11_front.jpg)}}{{thumbnail(simtrace_connectors_scaled.png)}}
9 1 laforge
10 31 tsaitgaist
You can buy the device on the "sysmocom shop":http://shop.sysmocom.de/products/simtrace.
11 1 laforge
12
13 31 tsaitgaist
h2. Connectors
14 1 laforge
15
16 31 tsaitgaist
* USB: USB mini-B connector. The main connector. The host software communicates (sniffing,...) through USB with the board. It can also be used to flash the micro-controller (using DFU).
17
* serial: 2.5 mm jack serial cable, as used by osmocomBB. port used to debug the device (printf goes there).
18
* debug (P2): same as serial, but using the FTDI serial cable. *It is recommended to cut the voltage wire of the 6pin FTDI connector before plugging the cable into the simtrace.*
19
* jtag (P1): JTAG 20 pin connector to do hardware assisted debugging.
20
* BT1: battery connector (4.5-6V DC). normally the USB provides power, but the battery port can be used for autonomous use of SIMtrace. The sniffed data can be saved in the flash (U1).
21
* FFC_SIM (P3): to connect the flat flexible cable with SIM end for the phone.
22
* SIM (P4): put your SIM in there (instead of in the phone)
23
* reset (SW1): to reset the board (not erasing the firmware). If your are too lazy to unplug and re-plug the USB.
24
* bootloader (SW2): used to start the bootloader to flash the device using DFU. press when plugging in the USB.
25
* test (JP1): short circuit using a jumper to flash using [[SIMtraceFirmware#EnteringtheSAM-BAmode|SAM-BA]].
26
* erase (JP2): short circuit using a jumper to completely erase the firmware.
27
28
29
h2. Schematics, Gerber & Co
30
31
32 2 laforge
The schematics, Gerber files, etc. can be found in the 'hardware' subdirectory of the simtrace.git repository:
33 31 tsaitgaist
* http://cgit.osmocom.org/cgit/simtrace/tree/hardware (web browsing)
34
* git://git.osmocom.org/simtrace (git clone URL)
35 15 laforge
36
We're using Kicad as EDA tool.  Most of the work on the schematics and Gerber files has been done by Kevin Redon,
37
based on the original design by Harald Welte.
38
39 1 laforge
The latest schematics are also available as an attachment to this page.
40
41
42 31 tsaitgaist
h2. Interconnections
43
44
45 1 laforge
The hardware schematics are very, very simple:
46
47 31 tsaitgaist
* Connect SIM-RST with PA7
48
* Connect SIM-I/O with PA6(TXD0) and PA1(TIOB0)
49
* Connect SIM-CLK with PA2(SCK0) and PA4(TCLK0)
50
* Connect SIM-GND with GND
51 15 laforge
52
53 31 tsaitgaist
h2. Mode of operation
54
55
56 25 laforge
The USART of the AT91SAM7S is capable of T=0. The documentation only mentions it in clock-master mode, like you
57
would run it in a smart card reader to actively talk to a smart card. However, by using the USART input clock multiplexer,
58
you can use an externally-generated CLK like the one from the SIM card socket of the phone.
59
60
Unfortunately, the Rx Timeout feature of the USART is not working in T=0 mode, so I had to re-implement Rx timeout (waiting time)
61
handling by means of the TC (timer/counter) block 0.  Due to technical limitations, we will wait up to one byte (12 etu) more
62 1 laforge
than we should.
63 25 laforge
64 1 laforge
65 31 tsaitgaist
h2. Modi
66
67
68 1 laforge
SIMtrace has the possibility to work as:
69 31 tsaitgaist
* sniffer
70
* card reader
71
* card emulator
72
* man-in-the-middle
73 1 laforge
74
The SAM7S offers 2 T=0 capable USART ports.
75
One is connected to the phone (PA21-PA27), the other to the SIM (PA1-PA7).
76 31 tsaitgaist
The lines goes from the phone to the SIM through a bus switch (IC4="CB3Q3244":http://www.ti.com/lit/ds/symlink/sn74cb3q3244.pdf).
77 1 laforge
The bus switch offer 2 buses of 4 lines:
78 31 tsaitgaist
* The first is used to forward RST, CLK, and VPP (between the SIM and the phone). It is controlled by SC_SW (PA20)
79
* The second is used to forward I/O (between the SIM and the phone). It is controlled by SC_I/O (PA19)
80 1 laforge
81
The various modi require to interrupt different lines:
82
83
|| SW_SC (PA20) || SC_I/O (PA19) || description || modus ||
84
|| L || L || phone and SIM directly connected || sniffer (use any USART port) ||
85
|| L || H || only I/O interrupted || MitM (use both USART port) ||
86
|| H || H || phone and SIM not connected || card read, emulator (use each USART port) ||
87
88
As of 2012-01-12, only the sniffer is implemented
89
90
SIM cards support various classes (voltage levels): class A = 5.0V, class B = 3.0V, class C = 1.8V.
91
SIMtrace v1.x only supports class B (3.0V), which all actual SIM cards and phone also support.
92
To ensure class B is used, SIMtrace forces 3.3V (within the 3.0V±10% spec) by holding the VCC line at this voltage.
93
SIMtrace v2 will support all 3 classes.
94 30 tsaitgaist
95 31 tsaitgaist
h2. Revisions
96 1 laforge
97 31 tsaitgaist
98
99
h3. v2.0
100
101 1 laforge
This is on going (stalled) work.
102 30 tsaitgaist
The changes compared to v1.x are:
103 31 tsaitgaist
* ID-1 and ID-000 smart card slots (with presence detection): so to be able to also sniff credit card sized smart cards
104
* through hole USB Mini-B and Serial/Jack 2.5 connector: to be more robust
105
* properly support all smart card classes (A,B,C): better compatibility
106 1 laforge
* be able to forward voltage from phone to SIM or provide voltage from the board: ideal sniffer and reader
107 31 tsaitgaist
* use an microSD slot instead of built-on flash: easier data transfer
108 1 laforge
* a SWP sniffer (maybe)
109
110 33 laforge
j3. v1.4p-SAM3 (unreleased, available upon request)
111 31 tsaitgaist
112 33 laforge
* switch from AT91SAM7S to AT91SAM3S: it has more USB endpoints
113
** firmware incomplete
114 1 laforge
115 33 laforge
h3. v1.4 / v1.4p
116 1 laforge
117 33 laforge
Changes:
118
* ensure PA0, PA1 and PA2 are high logic level at power-up (low interferes with SAM-BA operation)
119
** PA0 hard-wired to 3V#
120
** PA1 and PA2 get R25, R26 pull-up
121
* update to AT91SAM128D (previous we used AT91SAM128C which is now EOL)
122
* switch to alternative type of ferrite bead/filter, as old one is EOL
123
124
h3. v1.3
125
126 32 zecke
{{thumbnail(simtrace_v13_front.jpg)}}
127 30 tsaitgaist
128 1 laforge
Changes:
129
* added a FPF2109 power switch
130 31 tsaitgaist
* added a zener diode on LDO to SIM to provide ~3.0V to SIM (closer to ISO 7812 specified class B)
131
* it is now possible to choose the power source for the SIM card: provided by the SIMtrace on-board LDO, or forwarded from the phone
132
* no production customizations required
133
* silkscreen redone (sadly missing on the produced batch)
134 33 laforge
* change SPI flash to S25FL032P0XMFI011
135 1 laforge
136 31 tsaitgaist
*BUG:* because of this new feature (selecting power source for the SIM), we wanted to be able to identify the v1.3 board.
137 1 laforge
To do that, we tied PA0 to ground. But this needs to be HIGH for the AT91SAM7S to be able to enter it's SAM-BA mode (for flashing the first time).
138
If you produce the board yourself, you have to cut the path between the left upper pin and the capacitor.
139 31 tsaitgaist
The version is now written in flash. To flash the firmware the first time (only), follow the dedicated [[ProductionFlashingV13|instructions]].
140 24 tsaitgaist
141 26 tsaitgaist
Downloads:
142 31 tsaitgaist
* [attachment:simtrace_v13_schematic.pdf]
143
* [attachment:simtrace_v13_board.zip]
144 23 tsaitgaist
145
146 31 tsaitgaist
h3. v1.2p (1.2 Production branch)
147
148
149 32 zecke
{{thumbnail(simtrace_v12p_front.jpg)}}
150 1 laforge
151 23 tsaitgaist
adaptation of the v1.1p because of component availability for new batch.
152 1 laforge
153
Changes:
154 31 tsaitgaist
* capacitor is even nearer to the LDO
155
* one diode slightly changed place
156
* quartz crystal is smaller (footprint still fits)
157
* SIM slot is another (not available from Amphenol anymore). No presence switch.
158 1 laforge
159
Downloads:
160 31 tsaitgaist
* [attachment:simtrace_v12_schematic.pdf]
161
* [attachment:simtrace_v12p_gerber.zip]
162 1 laforge
163
164 31 tsaitgaist
h3. v1.1p (1.1 Production branch)
165
166
167 32 zecke
{{thumbnail(simtrace_11_front.jpg)}}
168 23 tsaitgaist
169
This is a slightly corrected version of the v1.0p.
170
171
Changes:
172 31 tsaitgaist
* a critical capacitor is near the LDO
173
* some other capacitors are nearer to the CPU
174
* some power traces are wider
175
* the SIM C6/VPP contact is also routed through the bus switch (sometimes used for Single Wire Protocol)
176
* sysmocom is added in the copper for legal reasons
177
* the FTDI Vcc is cut
178 20 tsaitgaist
179 7 laforge
Downloads:
180 31 tsaitgaist
* [attachment:simtrace_v11p_schematic.pdf]
181
* [attachment:simtrace_v11p_gerber.zip]
182 7 laforge
183
184 31 tsaitgaist
h3. v1.0p (1.0 Production branch)
185 22 tsaitgaist
186 31 tsaitgaist
187
188 32 zecke
{{thumbnail(simtrace_v10p_front_mid.jpg)}}
189 20 tsaitgaist
190
This is identical to v1.0 on the schematics side, we simply altered the footprints of some components to accommodate
191
whatever the SMT factory had in stock.  Specifically the LED are 0805 instead of 0603, and the shottky diodes are
192 7 laforge
in a slightly awkward looking very large package.
193
194
Downloads:
195 31 tsaitgaist
* [attachment:simtrace_v10p_schematic.pdf]
196
* [attachment:simtrace_v10p_gerber.zip]
197 7 laforge
198
199 31 tsaitgaist
h3. v1.0
200 20 tsaitgaist
201 31 tsaitgaist
202
203 32 zecke
{{thumbnail(simtrace_10_front.jpg)}}
204 1 laforge
205
This is the first stable release.  We built some 5 prototypes from this version.
206 7 laforge
207 1 laforge
Downloads:
208 31 tsaitgaist
* [attachment:simtrace_schem_v10.pdf]
209
* [attachment:simtrace_10_gerber.zip]
210 20 tsaitgaist
211
212 31 tsaitgaist
h3. v0.9
213
214
215 32 zecke
{{thumbnail(simtrace_v09_top_mid.jpg)}}
216 7 laforge
217 1 laforge
As of June 04, 2011 the components had all arrived and four PCBs were in production.  We assemble the first
218
units around June 14, 2011.
219
220
As of June 21st, we had four re-worked prototypes that are fully functional.
221
222 31 tsaitgaist
223 7 laforge
h3. v0.8
224 31 tsaitgaist
225
226 32 zecke
227 8 laforge
{{thumbnail(simtrace_08_front_mid.jpg)}}
228
229
Never really was an official release.  However, a friend took the unfinished Gerber files and built 5 units.
230
231
Since the Gerber was not finished, we had to do lots and lots of re-work in order to make them work at all.
232
233 31 tsaitgaist
h2. License
234
235
236 8 laforge
Schematics and Gerber files are released under the Creative Commons CC-BY-SA (Share Alike / Attribution) license.
237 1 laforge
238
239 31 tsaitgaist
h2. Sales
240 1 laforge
241
242 31 tsaitgaist
Sales started at the 2011 CCC Camp and the hardware can be bought through the web-shop of sysmocom GmbH ("h2. Credits
243
244
245
* Harald Welte
246
** Original project idea, schematic design
247
** Olimex SAM7-P64 based prototypes
248
** Firmware and host software
249
* Kevin Redon
250
** [[KiCAD]] work on schematics, footprints and routing
251
** Soldering of some prototypes
252
* [http://sysmocom.de/ sysmocom - systems for mobile communications GmbH":http://shop.sysmocom.de/])
253
** funding for hardware prototyping (PCB, components, etc)
254
* Christian Daniel
255
** post-production flashing + debugging, design + test of v1.0p rework
Add picture from clipboard (Maximum size: 48.8 MB)