ELSA MicroLink ISDN 2ab » History » Version 9
roox, 01/01/2023 10:59 PM
1 | 1 | laforge | h1. ELSA MicroLink ISDN 2a/b |
---|---|---|---|
2 | |||
3 | This is an ISDN terminal adapter with built-in a/b-Adapter for atraching analog devices (phones/modem) to an ISDN S0-bus. |
||
4 | |||
5 | 3 | laforge | {{thumbnail(ELSA_MicroLink_ISDN_2ab_front.jpg)}} |
6 | {{thumbnail(ELSA_MicroLink_ISDN_2ab_back.jpg)}} |
||
7 | {{thumbnail(ELSA_MicroLink_ISDN_2ab_bottom.jpg)}} |
||
8 | |||
9 | 4 | laforge | It appears to also have been sold as "ELSA Tango 2000", at least it shares the same firmware update files. |
10 | |||
11 | 1 | laforge | |Supply Voltage|24V AC| |
12 | 9 | roox | |Power Consumption|~4.2W (idle) - 4.5W| |
13 | 1 | laforge | |RS232 Connector|mini-DIN (adapter to DB9 + DB25 included)| |
14 | 7 | laforge | |Line Connector|RJ-11 (unusual for ISDN; 1:1 wiring (center four of RJ45 to center-four of RJ-11)| |
15 | 2 | laforge | |
16 | h2. MicroLink mini-DIN pin-out |
||
17 | |||
18 | 6 | laforge | See [[retro-bbs:Devolo_MicroLink_56k_Fun_II#MicroLink-mini-din-pin-out]] for the pin-out. |
19 | 4 | laforge | |
20 | h2. AT commands |
||
21 | |||
22 | h3. Setting the MSN |
||
23 | |||
24 | <pre> |
||
25 | 9 | roox | AT$IMSN=0,"MSN1","MSN2","MSN3" |
26 | 4 | laforge | </pre> |
27 | |||
28 | h3. Setting the bearer protocol |
||
29 | |||
30 | <pre> |
||
31 | 5 | laforge | Syntax: AT$IBP=<wert1> |
32 | 4 | laforge | |
33 | 5 | laforge | Parameter Wert Bedeutung |
34 | |||
35 | wert1 X75 X.75 Protokoll |
||
36 | X75T70 T70NL- Protokoll |
||
37 | V120 V.120 Protokoll |
||
38 | V110 V.110 Protokoll |
||
39 | HDLC HDLC - Protokoll |
||
40 | TRANS Transparent |
||
41 | HDLCP HDLC - PPP - Protokoll |
||
42 | BTX X.75, T.70NL und Cept/Kit |
||
43 | X75FB1 X.75 -> HDLCP |
||
44 | X75FB2 X.75 -> V.120 -> HDLCP |
||
45 | X75FB3 X.75 -> V.120 |
||
46 | 1 | laforge | V120FB1 V.120 -> HDLCP |
47 | </pre> |
||
48 | 9 | roox | |
49 | h3. Information |
||
50 | |||
51 | <pre> |
||
52 | ATI3 |
||
53 | Ver. 2.16 vom 06.10.1999 |
||
54 | |||
55 | ATI5 |
||
56 | 8819.000.428 E D 0000032832 |
||
57 | |||
58 | OK |
||
59 | ATI6 |
||
60 | ELSA MicroLink ISDN 2a/b |
||
61 | |||
62 | OK |
||
63 | ATI7 |
||
64 | CPU OK |
||
65 | INT OK |
||
66 | ROM OK |
||
67 | RAM OK |
||
68 | EEP OK |
||
69 | ISAC OK |
||
70 | HSCX OK |
||
71 | |||
72 | OK |
||
73 | ATI8 |
||
74 | OK |
||
75 | ATI9 |
||
76 | (#ELS8819\00000428\MODEM\ELS8865\ELSA MicroLink ISDN 2a/b00) |
||
77 | |||
78 | OK |
||
79 | |||
80 | </pre> |
||
81 | |||
82 | |||
83 | 4 | laforge | |
84 | h2. Documentation |
||
85 | |||
86 | * English User Manual: attachment:20651E.pdf |
||
87 | * English Installation Guide: attachment:20653.PDF |
||
88 | |||
89 | h2. Firmware |
||
90 | |||
91 | * 2.16: attachment:FW2AB.ZIP |
||
92 | 8 | laforge | |
93 | The firmware upgrade can be performed via X-modem after using the @AT$UPX@ command: |
||
94 | <pre> |
||
95 | AT$UPX |
||
96 | # |
||
97 | | Flash-Rom-Upload |
||
98 | | Ver. 1.02 / 27.01.98 |
||
99 | | Device: T2000 |
||
100 | |||
101 | please upload firmware by X-modem now, (quit: 2*Ctrl x) |
||
102 | </pre> |